- 您現在的位置：買賣IC網 > PDF目錄375377 > ATS535CSB (Allegro MicroSystems, Inc.) ZERO-SPEED, SELF-CALIBRATING, NON-ORIENTED, HALL-EFFECT GEAR-TOOTH SENSOR PDF資料下載
參數資料
| 型號： | ATS535CSB |
| 廠商： | Allegro MicroSystems, Inc. |
| 英文描述： | ZERO-SPEED, SELF-CALIBRATING, NON-ORIENTED, HALL-EFFECT GEAR-TOOTH SENSOR |
| 中文描述： | 零速度，自校準，無取向，霍爾效應齒輪齒傳感器 |
| 文件頁數： | 7/12頁 |
| 文件大小： | 75K |
| 代理商： | ATS535CSB |
ATS632LSC
HALL-EFFECT
GEAR-TOOTH SENSOR
SUBASSEMBLY
APPLICATIONS INFORMATION
Recommended Evaluation Technique.
The self-
calibrating feature of the ATS632LSC requires that a
special evaluation technique be used to measure its high-
accuracy performance capabilities. Installation inaccura-
cies are calibrated out at power on; hence, it is extremely
important that the device be re-powered at each air gap
when gathering timing accuracy data.
Self-Calibrating Functions.
This subassembly is
designed to minimize performance variation caused by
the large air gap variations resulting from installation by
self-calibrating at power-on. It is also designed to mini-
mize performance variation caused by the smaller, slower
air gap changes resulting from temperature change and
gear run-out during continuous operation by updating the
self-calibration periodically (after every 64 output pulses) if
necessary. These two functions should be tested using
the following procedure.
1.
Set the air gap to the desired value.
2.
Power down and then power on the device.
3.
Rotate the target at the desired speed.
4.
Wait for calibration to complete (16 output pulses to
occur).
5.
Monitor output for correct switching and measure
accuracy.
6.
Repeat the above for multiple air gaps within the
operating range of the device.
7.
This can be repeated over the entire temperature
range.
CRITERIA FOR DEVICE QUALIFICATION
All Allegro sensors are subjected to stringent qualification requirements prior to being released to production. To
become qualified, except for the destructive ESD tests, no failures are permitted.
Test Method and
Test Conditions
Samples
Per Lot
Qualification Test
Test Length
Comments
Temperature Humidity
Bias Life
JESD22-A101,
T
A
= 85
°
C, RH = 85%
1000 hrs
48
Device biased for
minimum power
Bias Life
JESD22-A108,
T
A
= 150
°
C, T
J
= 165
°
C
JESD22-A108,
T
A
= 175
°
C, T
J
= 190
°
C
1000 hrs
48
(Surge Operating Life)
168 hrs
48
Autoclave, Unbiased
JESD22-A102,
T
A
= 121
°
C, 15 psig
96 hrs
48
High-Temperature
(Bake) Storage Life
JESD22-A103,
T
A
= 170
°
C
1000 hrs
48
Temperature Cycle
JESD22-A104
1000 cycles
48
-55
°
C to +150
°
C
ESD,
Human Body Model
CDF-AEC-Q100-002
Pre/Post
Reading
3 per
test
Test to failure
All leads > 8 kV
相關PDF資料 |
PDF描述 |
|---|---|
| ATS535JSB | ZERO-SPEED, SELF-CALIBRATING, NON-ORIENTED, HALL-EFFECT GEAR-TOOTH SENSOR |
| ATS610LSA | DYNAMIC, PEAK-DETECTING, DIFFERENTIAL HALL-EFFECT GEAR-TOOTH SENSORS |
| ATS610LSC | DYNAMIC, PEAK-DETECTING, DIFFERENTIAL HALL-EFFECT GEAR-TOOTH SENSOR |
| ATS611LSB | Dynamic, Peak-Detecting,Differential Hall-Effect Gear-Tooth Sensor(動態，峰值檢測，差分霍爾效應齒輪嚙合傳感器) |
| ATS611 | TRUE ZERO-SPEED, HALL-EFFECT ADAPTIVE GEAR-TOOTH SENSOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ATS535JSB | 制造商:ALLEGRO 制造商全稱:Allegro MicroSystems 功能描述:ZERO-SPEED, SELF-CALIBRATING, NON-ORIENTED, HALL-EFFECT GEAR-TOOTH SENSOR |
| ATS-54150D-C0-R0 | 功能描述:HEATSINK 15X15X9.5MM W/OUT TIM RoHS:是 類別:風扇，熱管理 >> 熱敏 - 散熱器 系列:- 產品目錄繪圖:BDN12-3CB^A01 標準包裝:300 系列:BDN 類型:頂部安裝 冷卻式包裝:分類（BGA，LGA，CPU，ASIC……） 固定方法:散熱帶，粘合劑（含） 形狀:方形，鰭片 長度:1.21"（30.73mm） 寬:1.210"（30.73mm） 直徑:- 機座外的高度（散熱片高度）:0.355"（9.02mm） 溫升時的功耗:- 在強制氣流下的熱敏電阻:在 400 LFM 時為6.8°C/W 自然環境下的熱電阻:19.6°C/W 材質:鋁 材料表面處理:黑色陽極化處理 產品目錄頁面:2681 (CN2011-ZH PDF) 其它名稱:294-1099 |
| ATS-54150D-C1-R0 | 功能描述:Heat Sink BGA Aluminum Top Mount 制造商:advanced thermal solutions inc. 系列:- 零件狀態:有效 類型:頂部安裝 冷卻封裝:BGA 接合方法:散熱帶，粘合劑（含） 形狀:方形，鰭片 長度:0.590"（14.99mm） 寬度:0.590"（14.99mm） 直徑:- 離基底高度（鰭片高度）:0.374"（9.50mm） 不同溫升時功率耗散:- 不同強制氣流時的熱阻:26.2°C/W @ 200 LFM 自然條件下熱阻:- 材料:鋁 材料鍍層:黑色陽極化處理 標準包裝:10 |
| ATS-54150D-C2-R0 | 功能描述:HEAT SINK 15MM X 15MM X 9.5MM RoHS:是 類別:風扇，熱管理 >> 熱敏 - 散熱器 系列:- 標準包裝:500 系列:- 其它名稱:AE10843 |
| ATS-54150K-C0-R0 | 功能描述:HEATSINK 15X15X14.5MM W/OUT TIM RoHS:是 類別:風扇，熱管理 >> 熱敏 - 散熱器 系列:- 產品目錄繪圖:BDN12-3CB^A01 標準包裝:300 系列:BDN 類型:頂部安裝 冷卻式包裝:分類（BGA，LGA，CPU，ASIC……） 固定方法:散熱帶，粘合劑（含） 形狀:方形，鰭片 長度:1.21"（30.73mm） 寬:1.210"（30.73mm） 直徑:- 機座外的高度（散熱片高度）:0.355"（9.02mm） 溫升時的功耗:- 在強制氣流下的熱敏電阻:在 400 LFM 時為6.8°C/W 自然環境下的熱電阻:19.6°C/W 材質:鋁 材料表面處理:黑色陽極化處理 產品目錄頁面:2681 (CN2011-ZH PDF) 其它名稱:294-1099 |
發布緊急采購，3分鐘左右您將得到回復。