- 您現在的位置：買賣IC網 > PDF目錄379695 > ATS50 (Electronic Theatre Controls, Inc.) LOW-VOLTAGE SOT-23 TEMPERATURE SENSOR PDF資料下載
參數資料
| 型號： | ATS50 |
| 廠商： | Electronic Theatre Controls, Inc. |
| 元件分類： | 溫度/濕度傳感器 |
| 英文描述： | LOW-VOLTAGE SOT-23 TEMPERATURE SENSOR |
| 中文描述： | 低壓SOT - 23封裝溫度傳感器 |
| 文件頁數： | 3/9頁 |
| 文件大小： | 266K |
| 代理商： | ATS50 |
- 3 -
Andigilog, Inc. 2003
www.andigilog.com
70A03202-004
aTS50
25
50
75
100
125
-25
-50 -40
0
1750
100
750
500
V
OUT
(mV)
Temperature (oC)
1500
Temp (oC) = (V
OUT
– 500mV) / 10mV/oC
Figure 1. aTS50 Output Voltage vs. Temperature
Mounting
The aTS50 can be easily mounted by gluing or
cementing it to a surface. In this case, its temperature
will be within about 0.2°C of the temperature of the
surface it is attached to if the ambient air temperature
is almost the same as the surface temperature. If the
air temperature is much higher or lower than the
surface temperature, the actual temperature of the
aTS50 die will be at an intermediate temperature
between the surface temperature and the air
temperature.
To ensure good thermal conductivity, the backside of
the aTS50 die is directly attached to the GND pin. The
lands and traces to the aTS50 will, of course, be part of
the printed circuit board, which is the object whose
temperature is being measured. These printed circuit
board lands and traces will not cause the aTS50’s
temperature to deviate from the desired temperature.
Alternatively, the aTS50 can be mounted inside a
sealed-end metal tube, and can then be dipped into a
bath or screwed into a threaded hole in a tank. As
with any IC, the aTS50 and accompanying wiring and
circuits must be kept insulated and dry to avoid
leakage and corrosion. This is especially true if the
circuit may operate at cold temperatures where
condensation can occur. Printed-circuit coatings and
varnishes such as Humiseal and epoxy paint or dips
can be used to ensure that moisture cannot corrode
the aTS50 or its connections.
相關PDF資料 |
PDF描述 |
|---|---|
| ATS50S3 | LOW-VOLTAGE SOT-23 TEMPERATURE SENSOR |
| ATS51 | LOW-VOLTAGE SOT-23 TEMPERATURE SENSOR WITH HIGH OUTPUT DRIVE |
| ATS51S3 | LOW-VOLTAGE SOT-23 TEMPERATURE SENSOR WITH HIGH OUTPUT DRIVE |
| ATT3030-125S44I | Field-Programmable Gate Arrays |
| ATT3020-125J68I | Field-Programmable Gate Arrays |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ATS-50170B-C1-R0 | 功能描述:散熱片 MAXIGRIP HTSNK 17 X 17 X 7.5 (MM) RoHS:否 制造商:Ampro By ADLINK 產品:Heat Sink Accessories 安裝風格:Through Hole 散熱片材料: 散熱片樣式: 熱阻: 長度: 寬度: 高度: 設計目的:Express-HRR |
| ATS-50170B-C2-R0 | 功能描述:HEAT SINK 17MM X 17MM X 7.5MM RoHS:是 類別:風扇，熱管理 >> 熱敏 - 散熱器 系列:maxiGRIP, maxiFLOW 標準包裝:500 系列:- 其它名稱:AE10843 |
| ATS-50170G-C1-R0 | 功能描述:散熱片 MAXIGRIP HTSNK 17 X 17 X 12.5 (MM) RoHS:否 制造商:Ampro By ADLINK 產品:Heat Sink Accessories 安裝風格:Through Hole 散熱片材料: 散熱片樣式: 熱阻: 長度: 寬度: 高度: 設計目的:Express-HRR |
| ATS-50170G-C2-R0 | 功能描述:HEAT SINK 17MM X 17MM X 12.5MM RoHS:是 類別:風扇，熱管理 >> 熱敏 - 散熱器 系列:maxiGRIP, maxiFLOW 產品目錄繪圖:BDN12-3CB^A01 標準包裝:300 系列:BDN 類型:頂部安裝 冷卻式包裝:分類（BGA，LGA，CPU，ASIC……） 固定方法:散熱帶，粘合劑（含） 形狀:方形，鰭片 長度:1.21"（30.73mm） 寬:1.210"（30.73mm） 直徑:- 機座外的高度（散熱片高度）:0.355"（9.02mm） 溫升時的功耗:- 在強制氣流下的熱敏電阻:在 400 LFM 時為6.8°C/W 自然環境下的熱電阻:19.6°C/W 材質:鋁 材料表面處理:黑色陽極化處理 產品目錄頁面:2681 (CN2011-ZH PDF) 其它名稱:294-1099 |
| ATS-50170P-C1-R0 | 功能描述:散熱片 MAXIGRIP HTSNK 17 X 17 X 17.5 (MM) RoHS:否 制造商:Ampro By ADLINK 產品:Heat Sink Accessories 安裝風格:Through Hole 散熱片材料: 散熱片樣式: 熱阻: 長度: 寬度: 高度: 設計目的:Express-HRR |
發布緊急采購，3分鐘左右您將得到回復。