- 您現在的位置：買賣IC網 > PDF目錄12037 > ATMEGA16HVA-4TU (Atmel)MCU AVR 16K FLASH 4MHZ 28-TSOP PDF資料下載
參數資料
| 型號： | ATMEGA16HVA-4TU |
| 廠商： | Atmel |
| 文件頁數： | 128/196頁 |
| 文件大小： | 0K |
| 描述： | MCU AVR 16K FLASH 4MHZ 28-TSOP |
| 產品培訓模塊： | MCU Product Line Introduction megaAVR Introduction |
| 標準包裝： | 234 |
| 系列： | AVR® ATmega |
| 核心處理器： | AVR |
| 芯體尺寸： | 8-位 |
| 速度： | 4MHz |
| 連通性： | SPI |
| 外圍設備： | 欠壓檢測/復位，POR，PWM，WDT |
| 輸入/輸出數： | 7 |
| 程序存儲器容量： | 16KB（8K x 16） |
| 程序存儲器類型： | 閃存 |
| EEPROM 大?。?/td> | 256 x 8 |
| RAM 容量： | 512 x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 1.8 V ~ 9 V |
| 數據轉換器： | A/D 5x12b |
| 振蕩器型： | 外部 |
| 工作溫度： | -20°C ~ 85°C |
| 封裝/外殼： | 28-TSSOP（0.465"，11.8mm 寬） |
| 包裝： | 托盤 |
| 配用： | ATSTK600-ND - DEV KIT FOR AVR/AVR32 ATSTK500-ND - PROGRAMMER AVR STARTER KIT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁當前第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁
37
8024A–AVR–04/08
ATmega8HVA/16HVA
Note that if a level triggered interrupt is used for wake-up from Power-save mode, the changed
level must be held for some time to wake up the MCU. Refer to ”External Interrupts” on page 56
for details.
When waking up from Power-save mode, there is a delay from the wake-up condition occurs
until the wake-up becomes effective. This allows the clock to restart and become stable after
having been stopped. The wake-up period is defined in ”Clock Sources” on page 25.
10.5
Power-off Mode
When the SM2..0 bits are written to 100 and the SE bit is set, the SLEEP instruction makes the
CPU shut down the Voltage Regulator, leaving only the Charger Detect Circuitry operational. To
ensure that the MCU enters Power-off mode only when intended, the SLEEP instruction must be
executed within 4 clock cycles after the SM2..0 bits are written. The MCU will reset when return-
ing from Power-off mode.
Note:
Before entering Power-off sleep mode, interrupts should be disabled by software. Otherwise inter-
rupts may prevent the SLEEP instruction from being executed within the time limit.
10.6
Power Reduction Register
The Power Reduction Register (PRR), see ”P(pán)RR0 – Power Reduction Register 0” on page 39,
provides a method to stop the clock to individual peripherals to reduce power consumption. The
current state of the peripheral is frozen and the I/O registers can not be read or written.
Resources used by the peripheral when stopping the clock will remain occupied, hence the
peripheral should in most cases be disabled before stopping the clock. Waking up a module,
which is done by clearing the bit in PRR, puts the module in the same state as before shutdown.
Module shutdown can be used in Idle mode and Active mode to significantly reduce the overall
power consumption. In all other sleep modes, the clock is already stopped.
10.7
Minimizing Power Consumption
There are several issues to consider when trying to minimize the power consumption in an AVR
controlled system. In general, sleep modes should be used as much as possible, and the sleep
mode should be selected so that as few as possible of the device’s functions are operating. All
functions not needed should be disabled. In particular, the following modules may need special
consideration when trying to achieve the lowest possible power consumption.
10.7.1
Watchdog Timer
If the Watchdog Timer is not needed in the application, the module should be turned off. If the
Watchdog Timer is enabled, it will be enabled in all sleep modes except Power-off. The Watch-
dog Timer current consumption is significant only in Power-save mode. Refer to ”Watchdog
Timer” on page 46 for details on how to configure the Watchdog Timer.
10.7.2
Port Pins
When entering a sleep mode, all port pins should be configured to use minimum power. The
most important is then to ensure that no pins drive resistive loads. In sleep modes where both
the I/O clock (clk
I/O) and the ADC clock (clkADC) are stopped, the input buffers of the device will
be disabled. This ensures that no power is consumed by the input logic when not needed. In
some cases, the input logic is needed for detecting wake-up conditions, and it will then be
enabled. Refer to the section ”Digital Input Enable and Sleep Modes” on page 67 for details on
which pins are enabled. If the input buffer is enabled and the input signal is left floating or have
an analog signal level close to V
REG/2, the input buffer will use excessive power.
相關PDF資料 |
PDF描述 |
|---|---|
| ATMEGA16HVA-4CKU | MCU AVR 16K FLASH 4MHZ 36-LGA |
| VE-B30-IY-F1 | CONVERTER MOD DC/DC 5V 50W |
| VJ1825Y123JBCAT4X | CAP CER 0.012UF 200V 5% X7R 1825 |
| VJ1825Y123JBEAT4X | CAP CER 0.012UF 500V 5% X7R 1825 |
| VJ1825Y183JBCAT4X | CAP CER 0.018UF 200V 5% X7R 1825 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ATMEGA16HVA-4TUR | 功能描述:8位微控制器 -MCU AVR batman 16KB FLSH 4 MHZ TSOP, 1.8-9V RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| ATMEGA16HVB | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit Microcontroller with 16K/32K Bytes In-System Programmable Flash |
| ATMEGA16HVB_09 | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit Microcontroller with 16K/32K Bytes In-System Programmable Flash |
| ATMEGA16HVB_1 | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit Microcontroller with 16K/32K Bytes In-System Programmable Flash |
| ATMEGA16HVB_10 | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit Microcontroller with 16K/32K Bytes In-System Programmable Flash |
發布緊急采購，3分鐘左右您將得到回復。