- 您現在的位置：買賣IC網 > PDF目錄19647 > ATF1502ASV-20JC44 (Atmel)IC CPLD 20NS 3.3V 44PLCC PDF資料下載
參數資料
| 型號： | ATF1502ASV-20JC44 |
| 廠商： | Atmel |
| 文件頁數： | 24/25頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC CPLD 20NS 3.3V 44PLCC |
| 標準包裝： | 27 |
| 系列： | ATF15xx |
| 可編程類型： | 系統內可編程（最少 10,000 次編程/擦除循環） |
| 最大延遲時間 tpd(1)： | 20.0ns |
| 電壓電源 - 內部： | 3 V ~ 3.6 V |
| 宏單元數： | 32 |
| 輸入/輸出數： | 32 |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 44-LCC（J 形引線） |
| 供應商設備封裝： | 44-PLCC |
| 包裝： | 管件 |
| 其它名稱： | ATF1502ASV20JC44 |
8
1615J–PLD–01/06
ATF1502ASV
Atmel provides ISP hardware and software to allow programming of the ATF1502ASV via the
PC. ISP is performed by using either a download cable, a comparable board tester or a simple
microprocessor interface.
When using the ISP hardware or software to program the ATF1502ASV devices, four I/O pins
must be reserved for the JTAG interface. However, the logic features that the macrocells have
associated with these I/O pins are still available to the design for burned logic functions.
To facilitate ISP programming by the Automated Test Equipment (ATE) vendors. Serial Vector
Format (SVF) files can be created by Atmel-provided software utilities.
ATF1502ASV devices can also be programmed using standard third-party programmers. With a
third-party programmer, the JTAG ISP port can be disabled, thereby allowing four additional I/O
pins to be used for logic.
Contact your local Atmel representatives or Atmel PLD applications for details.
6.1
ISP Programming Protection
The ATF1502ASV has a special feature that locks the device and prevents the inputs and I/O
from driving if the programming process is interrupted for any reason. The inputs and I/O default
to high-Z state during such a condition. In addition, the pin-keeper option preserves the previous
state of the input and I/O PMS during programming.
All ATF1502ASV devices are initially shipped in the erased state, thereby making them ready to
use for ISP.
Note:
For more information refer to the “Designing for In-System Programmability with Atmel CPLDs”
application note.
7.
JTAG-BST/ISP Overview
The JTAG boundary-scan testing is controlled by the Test Access Port (TAP) controller in the
ATF1502ASV. The boundary-scan technique involves the inclusion of a shift-register stage
(contained in a boundary-scan cell) adjacent to each component so that signals at component
boundaries can be controlled and observed using scan testing methods. Each input pin and I/O
pin has its own boundary-scan cell (BSC) to support boundary-scan testing. The ATF1502ASV
does not include a Test Reset (TRST) input pin because the TAP controller is automatically
reset at power-up. The five JTAG modes supported include: SAMPLE/PRELOAD, EXTEST,
BYPASS, IDCODE and HIGHZ. The ATF1502ASV’s ISP can be fully described using JTAG’s
BSDL as described in IEEE Standard 1149.1b. This allows ATF1502ASV programming to be
described and implemented using any one of the third-party development tools supporting this
standard.
The ATF1502ASV has the option of using four JTAG-standard I/O pins for boundary-scan test-
ing (BST) and in-system programming (ISP) purposes. The ATF1502ASV is programmable
through the four JTAG pins using the IEEE standard JTAG programming protocol established by
IEEE Standard 1149.1 using 5V TTL-level programming signals from the ISP interface for in-
system programming. The JTAG feature is a programmable option. If JTAG (BST or ISP) is not
needed, then the four JTAG control pins are available as I/O pins.
7.1
JTAG Boundary-scan Cell (BSC) Testing
The ATF1502ASV contains up to 32 I/O pins and four input pins, depending on the device type
and package type selected. Each input pin and I/O pin has its own boundary-scan cell (BSC) in
相關PDF資料 |
PDF描述 |
|---|---|
| HCC50DRXI-S734 | CONN EDGECARD 100PS DIP .100 SLD |
| VE-B0Z-CY-F3 | CONVERTER MOD DC/DC 2V 20W |
| MIC384-3YMM | IC SUPERVISR THERM LOC/REM 8MSOP |
| TAJP684M035RNJ | CAP TANT 0.68UF 35V 20% 0805 |
| PQ05VY3H3ZZ | IC REG LDO ADJ 3.5A TO263 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ATF1502ASV-20JI44 | 功能描述:CPLD - 復雜可編程邏輯器件 ASICS RoHS:否 制造商:Lattice 系列: 存儲類型:EEPROM 大電池數量:128 最大工作頻率:333 MHz 延遲時間:2.7 ns 可編程輸入/輸出端數量:64 工作電源電壓:3.3 V 最大工作溫度:+ 90 C 最小工作溫度:0 C 封裝 / 箱體:TQFP-100 |
| ATF1502ASVL-30AC44 | 功能描述:IC CPLD 32 MC 30NS EE 44TQFP 制造商:microchip technology 系列:ATF15xx 包裝:托盤 零件狀態:停產 可編程類型:系統內可編程（最少 10，000 次編程/擦除循環） 延遲時間 tpd（1）最大值:30.0ns 電源電壓 - 內部:3 V ~ 3.6 V 宏單元數:32 I/O 數:32 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:44-TQFP 供應商器件封裝:44-TQFP（10x10） 基本零件編號:ATF1502 標準包裝:154 |
| ATF1502ASVL-30JC44 | 功能描述:IC CPLD 32 MC 30NS EE 44PLCC 制造商:microchip technology 系列:ATF15xx 包裝:托盤 零件狀態:停產 可編程類型:系統內可編程（最少 10，000 次編程/擦除循環） 延遲時間 tpd（1）最大值:30.0ns 電源電壓 - 內部:3 V ~ 3.6 V 宏單元數:32 I/O 數:32 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:44-LCC（J 形引線） 供應商器件封裝:44-PLCC（16.59x16.59） 基本零件編號:ATF1502 標準包裝:27 |
| ATF1502BE | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:Highperformance CPLD |
| ATF1502BE-5AX44 | 功能描述:CPLD - 復雜可編程邏輯器件 32 MC CPLD 1.8V ISP RoHS:否 制造商:Lattice 系列: 存儲類型:EEPROM 大電池數量:128 最大工作頻率:333 MHz 延遲時間:2.7 ns 可編程輸入/輸出端數量:64 工作電源電壓:3.3 V 最大工作溫度:+ 90 C 最小工作溫度:0 C 封裝 / 箱體:TQFP-100 |
發布緊急采購，3分鐘左右您將得到回復。