- 您現在的位置：買賣IC網 > PDF目錄381515 > AT93C57-10PI (ATMEL CORP) 3-Wire Serial EEPROMs PDF資料下載
參數資料
| 型號： | AT93C57-10PI |
| 廠商： | ATMEL CORP |
| 元件分類： | DRAM |
| 英文描述： | 3-Wire Serial EEPROMs |
| 中文描述： | 256 X 8 MICROWIRE BUS SERIAL EEPROM, PDIP8 |
| 封裝： | 0.300 INCH, PLASTIC, DIP-8 |
| 文件頁數： | 6/15頁 |
| 文件大?。?/td> | 154K |
| 代理商： | AT93C57-10PI |
AT93C46/56/57/66
6
Functional Description
The AT93C46/56/57/66 is accessed via a simple and ver-
satile 3-wire serial communication interface. Device opera-
tion is controlled by seven instructions issued by the host
processor.
A valid instruction starts with a rising edge
of CS
and consists of a Start Bit (logic ‘1’) followed by the
appropriate Op Code and the desired memory Address
location.
READ (READ):
The Read (READ) instruction contains
the Address code for the memory location to be read. After
the instruction and address are decoded, data from the
selected memory location is available at the serial output
pin DO. Output data changes are synchronized with the ris-
ing edges of serial clock SK. It should be noted that a
dummy bit (logic ‘0’) precedes the 8- or 16-bit data output
string.
ERASE/WRITE (EWEN):
To assure data integrity, the
part automatically goes into the Erase/Write Disable
(EWDS) state when power is first applied. An Erase/Write
Enable (EWEN) instruction must be executed first before
any programming instructions can be carried out. Please
note that once in the Erase/Write Enable state, program-
ming remains enabled until an Erase/Write Disable
(EWDS) instruction is executed or V
CC
power is removed
from the part.
ERASE (ERASE):
The Erase (ERASE) instruction pro-
grams all bits in the specified memory location to the logical
‘1’ state. The self-timed erase cycle starts once the ERASE
instruction and address are decoded. The DO pin outputs
the READY/BUSY status of the part if CS is brought high
after being kept low for a minimum of 250 ns (t
CS
). A logic
‘1’ at pin DO indicates that the selected memory location
has been erased, and the part is ready for another instruc-
tion.
WRITE (WRITE):
the 8 or 16 bits of data to be written into the specified mem-
ory location. The self-timed programming cycle, t
WP
, starts
after the last bit of data is received at serial data input pin
DI. The DO pin outputs the READY/BUSY status of the part
if CS is brought high after being kept low for a minimum of
250 ns (t
CS
). A logic ‘0’ at DO indicates that programming is
still in progress. A logic ‘1’ indicates that the memory loca-
tion at the specified address has been written with the data
pattern contained in the instruction and the part is ready for
further instructions.
A READY/BUSY status cannot be
obtained if the CS is brought high after the end of the
self-timed programming cycle, t
WP
.
ERASE ALL (ERAL):
The Erase All (ERAL) instruction
programs every bit in the memory array to the logic ‘1’ state
and is primarily used for testing purposes. The DO pin out-
puts the READY/BUSY status of the part if CS is brought
high after being kept low for a minimum of 250 ns (t
CS
). The
ERAL instruction is valid only at V
CC
= 5.0V
±
10%.
WRITE ALL (WRAL)
:
The Write All (WRAL) instruction
programs all memory locations with the data patterns spec-
ified in the instruction. The DO pin outputs the
READY/BUSY status of the part if CS is brought high after
being kept low for a minimum of 250 ns (t
CS
). The WRAL
instruction is valid only at V
CC
= 5.0V
±
10%.
ERASE/WRITE DISABLE (EWDS):
accidental data disturb, the Erase/Write Disable (EWDS)
instruction disables all programming modes and should be
executed after all programming operations. The operation
of the READ instruction is independent of both the EWEN
and EWDS instructions and can be executed at any time.
The Write (WRITE) instruction contains
To protect against
Instruction Set for the AT93C56 and AT93C66
Instruction
SB
Op
Code
Address
Data
Comments
x 8
x 16
x 8
x 16
READ
1
10
A
8
- A
0
A
7
- A
0
Reads data stored in memory, at
specified address.
EWEN
1
00
11XXXXXXX
11XXXXXX
Write enable must precede all
programming modes.
ERASE
1
11
A
8
- A
0
A
7 -
A
0
Erases memory location A
n
- A
0
.
WRITE
1
01
A
8
- A
0
A
7
- A
0
D
7
- D
0
D
15
- D
0
Writes memory location A
n
- A
0
.
ERAL
1
00
10XXXXXXX
10XXXXXX
Erases all memory locations. Valid
only at V
CC
= 4.5V to 5.5V.
WRAL
1
00
01XXXXXXX
01XXXXXX
D
7
- D
0
D
15
- D
0
Writes all memory locations. Valid
when V
CC
= 5.0V
±
10% and Disable
Register cleared.
EWDS
1
00
00XXXXXXX
00XXXXXX
Disables all programming instructions.
相關PDF資料 |
PDF描述 |
|---|---|
| AT93C57-10PI-2.7 | 3-Wire Serial EEPROMs |
| AT93C57-10SC | 3-Wire Serial EEPROMs |
| AT93C57-10SC-2.7 | SH2 Series, 7606 Group, UBC, SDRAM, PCMCIA, Host I/F, 2-ch CMT, 16KB unified 4 way set associative cache BP-176V; Vcc= 3.0 to 3.6 volts, Temp= -20 to 75 C; Package: PLBG0176GA-A |
| AT93C57-10SI | SH2 Series, 7606 Group, UBC, SDRAM, PCMCIA, Host I/F, 2-ch CMT, 16KB unified 4 way set associative cache BP-176V; Vcc= 3.0 to 3.6 volts, Temp= -20 to 75 C; Package: PLBG0176GA-A |
| AT93C57-10SI-2.7 | SH2 Series, 7606 Group, UBC, SDRAM, PCMCIA, Host I/F, 2-ch CMT, 16KB unified 4 way set associative cache BP-176V; Vcc= 3.0 to 3.6 volts, Temp= -40 to 85 C; Package: PLBG0176GA-A |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AT93C57-10PI-1.8 | 功能描述:IC EEPROM 2KBIT 2MHZ 8DIP RoHS:否 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:96 系列:- 格式 - 存儲器:閃存 存儲器類型:FLASH 存儲容量:16M（2M x 8，1M x 16） 速度:70ns 接口:并聯 電源電壓:2.65 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 封裝/外殼:48-TFSOP（0.724"，18.40mm 寬） 供應商設備封裝:48-TSOP 包裝:托盤 |
| AT93C57-10PI-2.5 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microwire Serial EEPROM |
| AT93C57-10PI-2.7 | 功能描述:IC EEPROM 2KBIT 2MHZ 8DIP RoHS:否 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:96 系列:- 格式 - 存儲器:閃存 存儲器類型:FLASH 存儲容量:16M（2M x 8，1M x 16） 速度:70ns 接口:并聯 電源電壓:2.65 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 封裝/外殼:48-TFSOP（0.724"，18.40mm 寬） 供應商設備封裝:48-TSOP 包裝:托盤 |
| AT93C57-10PM | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microwire Serial EEPROM |
| AT93C57-10SC | 功能描述:IC EEPROM 2KBIT 2MHZ 8SOIC RoHS:否 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:96 系列:- 格式 - 存儲器:閃存 存儲器類型:FLASH 存儲容量:16M（2M x 8，1M x 16） 速度:70ns 接口:并聯 電源電壓:2.65 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 封裝/外殼:48-TFSOP（0.724"，18.40mm 寬） 供應商設備封裝:48-TSOP 包裝:托盤 |
發布緊急采購，3分鐘左右您將得到回復。