- 您現(xiàn)在的位置：買賣IC網 > PDF目錄11202 > AT91SAM7SE256-CU-999 (Atmel)IC MCU ARM7 256KB FLASH 144LFBGA PDF資料下載
參數資料
| 型號： | AT91SAM7SE256-CU-999 |
| 廠商： | Atmel |
| 文件頁數： | 19/47頁 |
| 文件大小： | 0K |
| 描述： | IC MCU ARM7 256KB FLASH 144LFBGA |
| 產品培訓模塊： | MCU Product Line Introduction |
| 標準包裝： | 3,000 |
| 系列： | SAM7SE |
| 核心處理器： | ARM7 |
| 芯體尺寸： | 16/32-位 |
| 速度： | 55MHz |
| 連通性： | EBI/EMI，I²C，SPI，SSC，UART/USART，USB |
| 外圍設備： | 欠壓檢測/復位，POR，PWM，WDT |
| 輸入/輸出數： | 88 |
| 程序存儲器容量： | 256KB（256K x 8） |
| 程序存儲器類型： | 閃存 |
| RAM 容量： | 32K x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 1.65 V ~ 1.95 V |
| 數據轉換器： | A/D 8x10b |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 144-LFBGA |
| 包裝： | 帶卷 (TR) |
| 配用： | AT91SAM7SE-EK-ND - EVAL BOARD FOR AT91SAM7SE AT91SAM-ICE-ND - EMULATOR FOR AT91 ARM7/ARM9 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁
26
6222GS–ATARM–6-Sep-11
SAM7SE512/256/32 Summary
The security bit can only be enabled through the Command “Set Security Bit” of the EFC User
Interface. Disabling the security bit can only be achieved by asserting the ERASE pin at 1 and
after a full flash erase is performed. When the security bit is deactivated, all accesses to the
flash are permitted.
It is important to note that the assertion of the ERASE pin should always be longer than 200 ms.
As the ERASE pin integrates a permanent pull-down, it can be left unconnected during normal
operation. However, it is safer to connect it directly to GND for the final application.
8.1.2.5
Non-volatile Brownout Detector Control
Two general purpose NVM (GPNVM) bits are used for controlling the brownout detector (BOD),
so that even after a power loss, the brownout detector operations remain in their state.
These two GPNVM bits can be cleared or set respectively through the commands “Clear Gen-
eral-purpose NVM Bit” and “Set General-purpose NVM Bit” of the EFC User Interface.
GPNVM bit 0 is used as a brownout detector enable bit. Setting the GPNVM bit 0 enables the
BOD, clearing it disables the BOD. Asserting ERASE clears the GPNVM bit 0 and thus
disables the brownout detector by default.
GPNVM bit 1 is used as a brownout reset enable signal for the reset controller. Setting the
GPNVM bit 1 enables the brownout reset when a brownout is detected, Clearing the GPNVM
bit 1 disables the brownout reset. Asserting ERASE disables the brownout reset by default.
8.1.2.6
Calibration Bits
Sixteen NVM bits are used to calibrate the brownout detector and the voltage regulator. These
bits are factory configured and cannot be changed by the user. The ERASE pin has no effect on
the calibration bits.
8.1.3
Fast Flash Programming Interface
The Fast Flash Programming Interface allows programming the device through either a serial
JTAG interface or through a multiplexed fully-handshaked parallel port. It allows gang-program-
ming with market-standard industrial programmers.
The FFPI supports read, page program, page erase, full erase, lock, unlock and protect
commands.
The Fast Flash Programming Interface is enabled and the Fast Programming Mode is entered
when the TST pin and the PA0 and PA1 pins are all tied high and PA2 tied to low.
The Flash of the SAM7SE512 is organized in 2048 pages of 256 bytes (dual plane). It reads
as 131,072 32-bit words.
The Flash of the SAM7SE256 is organized in 1024 pages of 256 bytes (single plane). It reads
as 65,536 32-bit words.
The Flash of the SAM7SE32 is organized in 256 pages of 128 bytes (single plane). It reads
as 32,768 32-bit words.
The Flash of the SAM7SE512/256 contains a 256-byte write buffer, accessible through a 32-
bit interface.
The Flash of the SAM7SE32 contains a 128-byte write buffer, accessible through a 32-bit
interface.
相關PDF資料 |
PDF描述 |
|---|---|
| IDTHS231P16NDG8 | IC SWITCH DUAL SPST 16QFN |
| VE-B4M-IW | CONVERTER MOD DC/DC 10V 100W |
| VE-B4L-IW | CONVERTER MOD DC/DC 28V 100W |
| AS1752V-T | IC SWITCH QUAD SPST 16TQFN |
| VE-B4K-IX | CONVERTER MOD DC/DC 40V 75W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AT91SAM7SE32 | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:Product Description |
| AT91SAM7SE32-AU | 功能描述:ARM微控制器 - MCU LQFP IND TEMP RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT |
| AT91SAM7SE32B-AU | 功能描述:ARM微控制器 - MCU LQFP Grn IT MRLB RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT |
| AT91SAM7SE32B-AUR | 功能描述:ARM微控制器 - MCU LQFP Green IND TEMP MRL B, T&R MRLC RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT |
| AT91SAM7SE32B-CU | 功能描述:ARM微控制器 - MCU BGA Grn IT MRL B RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT |
發(fā)布緊急采購，3分鐘左右您將得到回復。