參數資料
型號： AT89LP52-20JU
廠商： Atmel
文件頁數： 78/117頁
文件大?。?/td> 0K
描述： IC MCU 8051 8K FLASH SPI 44PLCC
標準包裝： 27
系列： 89LP
核心處理器： 8051
芯體尺寸： 8-位
速度： 20MHz
連通性： EBI/EMI，I²C，SPI，UART/USART
外圍設備： 欠壓檢測/復位，POR，PWM，WDT
輸入/輸出數： 36
程序存儲器容量： 8KB（8K x 8）
程序存儲器類型： 閃存
RAM 容量： 256 x 8
電壓 - 電源 (Vcc/Vdd)： 2.4 V ~ 5.5 V
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 44-LCC（J 形引線）
包裝： *
63
3709D–MICRO–12/11
AT89LP51/52
The Broadcast Address for each slave is created by taking the logic OR of SADDR and SADEN.
Zeros in this result are trended as don’t cares. In most cases, interpreting the don’t cares as
ones, the broadcast address will be FF hexadecimal.
Upon reset SADDR (SFR address 0A9H) and SADEN (SFR address 0B9H) are loaded with
“0”s. This produces a given address of all “don’t cares” as well as a Broadcast address of all
“don’t cares”. This effectively disables the Automatic Addressing mode and allows the microcon-
troller to use standard 80C51-type UART drivers which do not make use of this feature.
14.5
More About Mode 0
In Mode 0, the UART is configured as either a two wire half-duplex or three wire full-duplex syn-
chronous serial interface. In two-wire mode serial data enters and exits through RXD and TXD
outputs the shift clock. In three-wire mode serial data enters through MISO, exits through MOSI
and SCK outputs the shift clock. Eight data bits are transmitted/received, with the LSB first. Fig-
ure 14-3 and Figure 14-5 on page 67 show simplified functional diagrams of the serial port in
Mode 0 and associated timing. The baud rate is programmable to 1/2 or 1/4 the system fre-
quency by setting/clearing the SMOD1 bit in Fast mode, or 1/3 or 1/6 the system frequency in
Compatibility mode. However, changing SMOD1 has an effect on the relationship between the
clock and data as described below. The baud rate can also be generated by Timer 1 by setting
TB8. Table 14-4 lists the baud rate options for Mode 0.
14.5.1
Two-Wire (Half-Duplex) Mode
Transmission is initiated by any instruction that uses SBUF as a destination register. The “write
to SBUF” signal also loads a “1” into the 9th position of the transmit shift register and tells the TX
Control Block to begin a transmission. The internal timing is such that one full bit slot may elapse
between “write to SBUF” and activation of SEND.
SEND transfers the output of the shift register to the alternate output function line of P3.0, and
also transfers Shift Clock to the alternate output function line of P3.1. As data bits shift out to the
right, “0”s come in from the left. When the MSB of the data byte is at the output position of the
shift register, the “1” that was initially loaded into the 9th position is just to the left of the MSB,
and all positions to the left of that contain “0”s. This condition flags the TX Control block to do
one last shift, then deactivate SEND and set TI.
Reception is initiated by the condition REN = 1 and RI = 0. At the next clock cycle, the RX Con-
trol unit writes the bits 11111110B to the receive shift register and activates RECEIVE in the
next clock phase. RECEIVE enables Shift Clock to the alternate output function line of P3.1. As
data bits come in from the right, “1”s shift out to the left. When the “0” that was initially loaded
into the right-most position arrives at the left-most position in the shift register, it flags the RX
Control block to do one last shift and load SBUF. Then RECEIVE is cleared and RI is set.
The relationship between the shift clock and data is determined by the combination of the SM2
and SMOD1 bits as listed in Table 14-5 and shown in Figure . The SM2 bit determines the idle
Table 14-4.
Mode 0 Baud Rates
TB8
SMOD1
Baud Rate (Fast)
Baud Rate (Compatibility)
00
fSYS/4
fSYS/6
01
fSYS/2
fSYS/3
1
0
(Timer 1 Overflow) / 4
1
(Timer 1 Overflow) / 2
相關PDF資料
PDF描述
AT89S4051-24PU MCU 8051 4K FLASH 24MHZ 20-PDIP
AT89LP2052-20SU IC 8051 MCU FLASH 2K 20SOIC
AT89LP52-20AU IC MCU 8051 8K FLASH SPI 44TQFP
AT89LP52-20PU IC MCU 8051 8K FLASH SPI 40PDIP
ATMEGA48PA-MMN MCU AVR 4KB FLASH 20MHZ 28QFN
相關代理商/技術參數
參數描述
AT89LP52-20MU 功能描述:8位微控制器 -MCU Single-Cycle 8051 8K ISP Flash MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
AT89LP52-20PU 功能描述:8位微控制器 -MCU Single-Cycle 8051 8K ISP Flash MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
AT89LP6440-20AU 功能描述:8位微控制器 -MCU Single-Cycle 8051 64K ISP Flash RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
AT89LP6440-20JU 功能描述:8位微控制器 -MCU Single-Cycle 8051 64K ISP Flash RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
AT89LP6440-20MU 功能描述:8位微控制器 -MCU Single-Cycle 8051 64K ISP Flash RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*