參數資料
型號： AT89LP428-20JU
廠商： Atmel
文件頁數： 72/149頁
文件大?。?/td> 0K
描述： MCU 8051 4K FLASH SPI 32PLCC
產品培訓模塊： MCU Product Line Introduction
標準包裝： 32
系列： 89LP
核心處理器： 8051
芯體尺寸： 8-位
速度： 20MHz
連通性： SPI，UART/USART
外圍設備： 欠壓檢測/復位，POR，PWM，WDT
輸入/輸出數： 30
程序存儲器容量： 4KB（4K x 8）
程序存儲器類型： 閃存
EEPROM 大?。?/td> 512 x 8
RAM 容量： 768 x 8
電壓 - 電源 (Vcc/Vdd)： 2.4 V ~ 5.5 V
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 32-LCC（J 形引線）
包裝： 管件
29
3654A–MICRO–8/09
AT89LP428/828
9.
Interrupts
The AT89LP428/828 provides 10 interrupt sources: two external interrupts, three timer inter-
rupts, a serial port interrupt, an analog comparator interrupt, a GPI, a compare/capture interrupt
and an SPI interrupt. These interrupts and the system reset each have a separate program vec-
tor at the start of the program memory space. Each interrupt source can be individually enabled
or disabled by setting or clearing a bit in the interrupt enable registers IE and IE2. The IE register
also contains a global disable bit, EA, which disables all interrupts.
Each interrupt source can be individually programmed to one of four priority levels by setting or
clearing bits in the interrupt priority registers IP, IPH, IP2 and IP2H. An interrupt service routine
in progress can be interrupted by a higher priority interrupt, but not by another interrupt of the
same or lower priority. The highest priority interrupt cannot be interrupted by any other interrupt
source. If two requests of different priority levels are pending at the end of an instruction, the
request of higher priority level is serviced. If requests of the same priority level are pending at
the end of an instruction, an internal polling sequence determines which request is serviced. The
polling sequence is based on the vector address; an interrupt with a lower vector address has
higher priority than an interrupt with a higher vector address. Note that the polling sequence is
only used to resolve pending requests of the same priority level.
The IPxD bits located at the seventh bit of IP, IPH, IP2 and IP2H can be used to disable all inter-
rupts of a given priority level, allowing software implementations of more complex interrupt
priority handling schemes.
The External Interrupts INT0 and INT1 can each be either level-activated or edge-activated,
depending on bits IT0 and IT1 in Register TCON. The flags that actually generate these inter-
rupts are the IE0 and IE1 bits in TCON. When the service routine is vectored to, hardware clears
the flag that generated an external interrupt only if the interrupt was edge-activated. If the inter-
rupt was level activated, then the external requesting source (rather than the on-chip hardware)
controls the request flag.
Table 8-1.
PCON
– Power Control Register
PCON = 87H
Reset Value = 000X 0000B
Not Bit Addressable
SMOD1
SMOD0
PWDEX
POF
GF1
GF0
PD
IDL
Bit
7
6
543
21
0
Symbol
Function
SMOD1
Double Baud Rate Bit. Doubles the baud rate of the UART in Modes 1, 2, or 3.
SMOD0
Frame Error Select. When SMOD0 = 1, SCON.7 is SM0. When SMOD0 = 1, SCON.7 is FE. Note that FE will be set after
a frame error regardless of the state of SMOD0.
PWDEX
Power-down Exit Mode. When PWDEX = 1, wake up from Power-down is externally controlled. When PWDEX = 1, wake
up from Power-down is internally timed.
POF
Power Off Flag. POF is set to “1” during power up (i.e. cold reset). It can be set or reset under software control and is not
affected by RST or BOD (i.e. warm resets).
GF1, GF0
General-purpose Flags.
PD
Power-down Bit. Setting this bit activates power-down operation.
IDL
Idle Mode Bit. Setting this bit activates Idle mode operation
相關PDF資料
PDF描述
ATMEGA48V-10MU IC AVR MCU 4K 10MHZ 1.8V 32-QFN
ATMEGA48-20MU IC AVR MCU 4K 20MHZ 5V 32-QFN
ATMEGA48V-10AU IC AVR MCU 4K 10MHZ 1.8V 32TQFP
ATMEGA48-20AU IC AVR MCU 4K 20MHZ 5V 32TQFP
ATTINY2313-20MU IC MCU AVR 2K FLASH 20-QFN
相關代理商/技術參數
參數描述
AT89LP428-20MH 功能描述:8位微控制器 -MCU SingleCycle 8051 4K ISP Flash 2.4V RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
AT89LP428-20PU 功能描述:8位微控制器 -MCU SingleCycle 8051 4K ISP Flash 2.4V RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
AT89LP51-20AU 功能描述:8位微控制器 -MCU Single Cycle 8051 4K ISP FL RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
AT89LP51-20JU 功能描述:8位微控制器 -MCU Single Cycle 8051 4K ISP FL RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
AT89LP51-20MU 功能描述:8位微控制器 -MCU Single Cycle 8051 4K ISP FL RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*