參數資料
型號： AT89C51IC2-SLSUL
廠商： Atmel
文件頁數： 6/140頁
文件大小： 0K
描述： IC 8051 MCU FLASH 32K 44PLCC
產品培訓模塊： MCU Product Line Introduction
標準包裝： 972
系列： 89C
核心處理器： 8051
芯體尺寸： 8-位
速度： 60MHz
連通性： I²C，SPI，UART/USART
外圍設備： POR，PWM，WDT
輸入/輸出數： 34
程序存儲器容量： 32KB（32K x 8）
程序存儲器類型： 閃存
RAM 容量： 1.25K x 8
電壓 - 電源 (Vcc/Vdd)： 2.7 V ~ 3.6 V
振蕩器型： 外部
工作溫度： -40°C ~ 85°C
封裝/外殼： 44-LCC（J 形引線）
包裝： 管件
配用： AT89OCD-01-ND - USB EMULATOR FOR AT8XC51 MCU
103
AT89C51IC2
4301D–8051–02/08
Table 80. WDTPRG Register
WDTPRG - Watchdog Timer Out Register (0A7h)
Reset value XXXX X000
WDT During Power Down
and Idle
In Power Down mode the oscillator stops, which means the WDT also stops. While in
Power Down mode the user does not need to service the WDT. There are 2 methods of
exiting Power Down mode: by a hardware reset or via a level activated external inter-
rupt which is enabled prior to entering Power Down mode. When Power Down is exited
with hardware reset, servicing the WDT should occur as it normally should whenever the
AT89C51IC2 is reset. Exiting Power Down with an interrupt is significantly different. The
interrupt is held low long enough for the oscillator to stabilize. When the interrupt is
brought high, the interrupt is serviced. To prevent the WDT from resetting the device
while the interrupt pin is held low, the WDT is not started until the interrupt is pulled high.
It is suggested that the WDT be reset during the interrupt service routine.
To ensure that the WDT does not overflow within a few states of exiting of powerdown, it
is better to reset the WDT just before entering powerdown.
In the Idle mode, the oscillator continues to run. To prevent the WDT from resetting the
AT89C51IC2 while in Idle mode, the user should always set up a timer that will periodi-
cally exit Idle, service the WDT, and re-enter Idle mode.
7
6
5
4
3
2
1
0
-
S2
S1
S0
Bit
Number
Bit
Mnemonic Description
7
-
Reserved
The value read from this bit is undetermined. Do not try to set this bit.
6
-
5
-
4
-
3
-
2
S2
WDT Time-out select bit 2
1
S1
WDT Time-out select bit 1
0
S0
WDT Time-out select bit 0
S2
S1 S0Selected Time-out
0
00
(214 - 1) machine cycles, 16. 3 ms @ F
OSCA =12 MHz
0
01
(215 - 1) machine cycles, 32.7 ms @ FOSCA=12 MHz
0
10 (216 - 1) machine cycles, 65. 5 ms @ F
OSCA=12 MHz
0
11
(217 - 1) machine cycles, 131 ms @ F
OSCA=12 MHz
1
00
(218 - 1) machine cycles, 262 ms @ FOSCA=12 MHz
1
01 (219 - 1) machine cycles, 542 ms @ F
OSCA=12 MHz
1
10
(220 - 1) machine cycles, 1.05 s @ F
OSCA=12 MHz
1
11
(221 - 1) machine cycles, 2.09 s @ FOSCA=12 MHz
相關PDF資料
PDF描述
VI-JT3-IW CONVERTER MOD DC/DC 24V 100W
VE-B4N-IW CONVERTER MOD DC/DC 18.5V 100W
IDTQS4A101QG8 IC SWITCH QUAD SPST 16QSOP
ATSAM3A4CA-CU IC MCU 2X128KB CORTEX-M3 100-BGA
VE-B4M-IX CONVERTER MOD DC/DC 10V 75W
相關代理商/技術參數
參數描述
AT89C51IC2-SLSUM 功能描述:8位微控制器 -MCU C51IC2 32K FLASH I2C 32KHz 5V RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
AT89C51ID2 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit Flash Microcontroller
AT89C51ID2_0309 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit Flash Microcontroller
AT89C51ID2_05 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit Flash Microcontroller
AT89C51ID2-IM 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit Flash Microcontroller
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*