- 您現在的位置：買賣IC網 > PDF目錄1903 > AT85C51SND3B1-RTTUL (Atmel)IC DECODER/ENCODER DGTL 100-LQFP PDF資料下載
參數資料
| 型號： | AT85C51SND3B1-RTTUL |
| 廠商： | Atmel |
| 文件頁數： | 82/119頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DECODER/ENCODER DGTL 100-LQFP |
| 標準包裝： | 90 |
| 類型： | 音頻編碼器/解碼器 |
| 應用： | 移動電話，手機，視頻顯示器 |
| 電壓 - 電源，數字： | 1.65 V ~ 3.6 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 100-LQFP |
| 供應商設備封裝： | 100-LQFP（14x14） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁當前第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁
65
AT85C51SND3B
7632D–MP3–01/07
Timers/Counters
The AT85C51SND3B derivatives implement 2 general-purpose, 16-bit Timers/Counters.
They are identified as Timer 0 and Timer 1, and can be independently configured to
operate in a variety of modes as a Timer or as an event Counter. When operating as a
Timer, the Timer/Counter runs for a programmed length of time, then issues an interrupt
request. When operating as a Counter, the Timer/Counter counts negative transitions
on an external pin. After a preset number of counts, the Counter issues an interrupt
request.
The various operating modes of each Timer/Counter are described in the following
sections.
Timer/Counter
Operations
For instance, a basic operation is Timer registers THx and TLx (x = 0, 1) connected in
cascade to form a 16-bit Timer. Setting the run control bit (TRx) in TCON register (see
Table 81) turns the Timer on by allowing the selected input to increment TLx. When TLx
overflows it increments THx; when THx overflows it sets the Timer overflow flag (TFx) in
TCON register. Setting the TRx does not clear the THx and TLx Timer registers. Timer
registers can be accessed to obtain the current count or to enter preset values. They
can be read at any time but TRx bit must be cleared to preset their values, otherwise,
the behavior of the Timer/Counter is unpredictable.
The C/Tx# control bit selects Timer operation or Counter operation by selecting the
divided-down peripheral clock or external pin Tx as the source for the counted signal.
TRx bit must be cleared when changing the mode of operation, otherwise the behavior
of the Timer/Counter is unpredictable.
For Timer operation (C/Tx# = 0), the Timer register counts the divided-down peripheral
clock. The Timer register is incremented once every peripheral cycle (6 peripheral clock
periods). The Timer clock rate is FPER/6, i.e., FOSC/12 in standard mode or FOSC/6 in X2
mode.
For Counter operation (C/Tx# = 1), the Timer register counts the negative transitions on
the Tx external input pin. The external input is sampled every peripheral cycles. When
the sample is high in one cycle and low in the next one, the Counter is incremented.
Since it takes 2 cycles (12 peripheral clock periods) to recognize a negative transition,
the maximum count rate is FPER/12, i.e., FOSC/24 in standard mode or FOSC/12 in X2
mode. There are no restrictions on the duty cycle of the external input signal, but to
ensure that a given level is sampled at least once before it changes, it should be held for
at least one full peripheral cycle.
Timer Clock Controller
As shown in Figure 31, the Timer 0 (FT0) and Timer 1 (FT1) clocks are derived from
either the peripheral clock (FPER) or the oscillator clock (FOSC) depending on the T0X2
and T1X2 bits in CKCON register. These clocks are issued from the Clock Controller
block as detailed in Section “Oscillator”, page 28. When T0X2 or T1X2 bit is set, the
Timer 0 or Timer 1 clock frequency is fixed and equal to the oscillator clock frequency
divided by 2. When cleared, the Timer clock frequency is equal to the oscillator clock fre-
quency divided by 2 in standard mode or to the oscillator clock frequency in X2 mode.
相關PDF資料 |
PDF描述 |
|---|---|
| AT87251G2D-RLTUM | IC MCU 8/16BIT 32K OTP 44-VQFP |
| AT87C51RB2-SLRUM | MCU ROMLESS 16K OTP 44-PLCC |
| AT87C52X2-RLRUM | MCU ROMLESS 32X2 3V 44-VQFP |
| AT87C58X2-SLRUM | MCU 8051 32K EPROM 44PLCC |
| AT87F51-24PI | IC MICRO CTRL 24MHZ 40DIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AT85C51SND3B2-RTTUL | 功能描述:音頻 DSP Microcontroller RoHS:否 制造商:Texas Instruments 工作電源電壓: 電源電流: 工作溫度范圍: 安裝風格: 封裝 / 箱體: 封裝:Tube |
| AT85C51SND3BX | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:MP3 Microcontrollers |
| AT85C51SND4B1-7FTUL | 功能描述:音頻 DSP Microcontroller RoHS:否 制造商:Texas Instruments 工作電源電壓: 電源電流: 工作溫度范圍: 安裝風格: 封裝 / 箱體: 封裝:Tube |
| AT85DVK-07 | 功能描述:開發板和工具包 - 8051 DEV Kit SND3 RoHS:否 制造商:Silicon Labs 產品:Development Kits 工具用于評估:C8051F960, Si7005 核心: 接口類型:USB 工作電源電壓: |
| AT85EC5122 | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:MICROCONTROLLER WITH USB AND SMART CARD READER INTERFACES |
發布緊急采購，3分鐘左右您將得到回復。