參數資料
型號: ASC7611QS24
廠商: Electronic Theatre Controls, Inc.
英文描述: HARDWARE MONITOR WITH INTEGRATED FAN CONTROL
中文描述: 五金顯示器整合了風扇控制
文件頁數: 24/40頁
文件大?。?/td> 505K
代理商: ASC7611QS24
P
P
- 24 -
Andigilog, Inc. 2006
www.andigilog.com
October 2006 - 70A05007
aSC7611
Fan Register Device Set-Up
The BIOS will follow the following steps to configure the fan registers on the aSC7611. The registers corresponding to each
function are listed. All steps may not be necessary if default values are acceptable. Regardless of all changes made by the
BIOS to the fan limit and parameter registers during configuration, the aSC7611 will continue to operate based on default
values until the START bit (bit 0), in the Ready/Lock/Start/Override register (address 40h), is set. Once the fan mode is
updated, by setting the START bit to 1, the aSC7611 will operate using the values that were set by the BIOS in the fan
control limit and parameter registers (address in the range 5Ch through 75h).
1. Set limits and parameters (not necessarily in this order):
[5F-61h] Set PWM frequency for the fan and auto fan control range for each zone.
[62-63h] Set spike smoothing and min/off.
[5C-5Eh] Set the fan spin-up delay.
[75h] Set PWM spin-up mode to terminate after time set in [5Ch]. Value = 00h instead of default 01h.
[5Ch] Match fan with a corresponding thermal zone.
[67-69h] Set the fan temperature limits.
[6A-6Ch] Set the temperature absolute limits.
[64-66h] Set the PWM minimum duty cycle.
[6D-6Eh] Set the temperature hysteresis values.
2. [40h] Set bit 0 (START) to update fan control and limit register values and start fan control based on these new
values.
[40h] (Optional) Set bit 1 (LOCK) to lock the fan limit and parameter registers.
WARNING:
this is a
non-reversible
change in state and locks out further change in critical fan control parameters until power is removed from the aSC7611.
Register 5F-61h: Auto Fan Speed Range, PWM Frequency
Register
Address
Read/
Write
Register Name
Bit 7
(MSB)
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
(LSB)
Default
Value
Lock
5Fh
R/W
Zone 1 Range
Fan1 Frequency
RAN3
RAN2
RAN1
RAN0
HLFRQ
FRQ2
FRQ1
FRQ0
C3
X
60h
R/W
Zone 2 Range/
Fan 2 Frequency
RAN3
RAN2
RAN1
RAN0
HLFRQ
FRQ2
FRQ1
FRQ0
C3
X
61h
R/W
Zone 3 Range/
Fan 3 Frequency
RAN3
RAN2
RAN1
RAN0
HLFRQ
FRQ2
FRQ1
FRQ0
C3
X
In Auto Fan Mode, when the temperature for a zone is above the Temperature Limit (Registers 67-69h) and below its
Absolute Temperature Limit (Registers 6A-6Ch), the speed of a fan assigned to that zone is determined as follows:
When the temperature reaches the Fan Temp Limit for a zone, the PWM output assigned to that zone will be Fan PWM
Minimum. Between Fan Temp Limit and (Fan Temp Limit + Range), the PWM duty cycle will increase linearly according to
the temperature as shown in the figure below. The PWM duty cycle will be 100% at (Fan Temp Limit + Range).
PWM frequency - FRQ[3:0] and HLFRQ
The PWM frequency bits [3:0] determine the PWM frequency for the fan. The aSC7611 has high and low frequency ranges
for the PWM outputs that are controlled by the HLFRQ bit.
PWM Frequency Selection (Default = 0011
30 Hz).
相關PDF資料
PDF描述
ASC7621 HARDWARE MONITOR WITH INTEGRATED FAN CONTROL
ASC7621QS24 HARDWARE MONITOR WITH INTEGRATED FAN CONTROL
ASD05H-12S5 Isolated and Regulated 5 WATT Open Frame DC/DC Converter
ASD05H-12S9 Isolated and Regulated 5 WATT Open Frame DC/DC Converter
ASD05H-48D12 Isolated and Regulated 5 WATT Open Frame DC/DC Converter
相關代理商/技術參數
參數描述
ASC7621 制造商:未知廠家 制造商全稱:未知廠家 功能描述:HARDWARE MONITOR WITH INTEGRATED FAN CONTROL
ASC7621QS24 制造商:未知廠家 制造商全稱:未知廠家 功能描述:HARDWARE MONITOR WITH INTEGRATED FAN CONTROL
ASC-8-2-CB (5-PIN) 制造商:Belden Inc 功能描述:ASC-8-2-CB (5-PIN)
ASC-8-2-LED PUR 10M(5-CONTACT) 制造商:Belden Inc 功能描述:ASC-8-2-LED PUR 10M(5-CONTACT)
ASC8848AETE 制造商:NXP Semiconductors 功能描述:IC VIDEO PROCESSOR ADV 484TFBGA 制造商:NXP Semiconductors 功能描述:ASC8848AET/TFBGA/TRAYBDP//