- 您現在的位置：買賣IC網 > PDF目錄2065 > AS1976-T (ams)IC COMPARATOR PUSH/PULL SOT23-5 PDF資料下載
參數資料
| 型號： | AS1976-T |
| 廠商： | ams |
| 文件頁數： | 5/18頁 |
| 文件大小： | 0K |
| 描述： | IC COMPARATOR PUSH/PULL SOT23-5 |
| 標準包裝： | 1 |
| 類型： | 通用 |
| 元件數： | 1 |
| 輸出類型： | CMOS，推挽式，滿擺幅 |
| 電壓 - 電源，單路/雙路(±)： | 1.8 V ~ 5.5 V |
| 電壓 - 輸入偏移（最小值）： | 5mV @ 5V |
| 電流 - 輸入偏壓（最小值）： | 0.001µA @ 5V |
| 電流 - 輸出（標準）： | 50mA |
| 電流 - 靜態（最大值）： | 500nA |
| CMRR, PSRR（標準）： | 74dB CMRR，86.02dB PSRR |
| 傳輸延遲（最大）： | 15ns |
| 磁滯： | 3mV |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | SC-74A，SOT-753 |
| 安裝類型： | 表面貼裝 |
| 包裝： | 標準包裝 |
| 其它名稱： | AS1976-TDKR |
www.austriamicrosystems.com
Revision 1.01
12 - 17
AS1976/AS1977
Data Sheet - A p p l i c a t i o n I n f o r m a t i o n
Additional Hysteresis (AS1976)
Additional hysteresis can be added to the AS1976 and AS1978 with three resistors and positive feedback (see Figure
27), however, this positive feedback method slows hysteresis response time.
Figure 27. AS1976 Additional Hysteresis
Resistor Selection Example
For the circuit shown in Figure 27, use the following steps to calculate values for R1, R2, and R3.
1. First select the value for R3. Leakage current at IN is less than 2nA, thus the current through R3 should be at least
0.2A to minimize errors due to leakage current. The current through R3 at the trip point is:
(VREF - VOUT)/R3
(EQ 1)
Taking into consideration the two possible output states, solving for R3 yields two formulas:
R3 = VREF/IR3
(EQ 2)
R3 = (VCC - VREF)/IR3
(EQ 3)
Use the smaller of the two resulting values for R3. For example, for VREF = 1.245V, VCC = 3.3V, and IR3 = 1A, the
two resistor values are 1.2M
Ω and 2.0MΩ, therefore choose a 1.2MΩ standard resistor for R3.
2. Choose the required hysteresis band (VHB). For this example, choose 33mV.
3. Calculate R1 as:
R1 = R3(VHB/VCC)(EQ 4)
Substituting the R1 and VHB example values gives:
R1 = 1.2M
Ω(50mV/3.3V) = 12kΩ
4. Choose the trip point for VIN rising (VTHR) such that VTHR > VREF(R1 + R3)/R3. For this example, choose 3V.
5. Calculate R2 as:
R2 = 1/[VTHR/(VREF x R1) - (1/R1) - (1/R3)]
(EQ 5)
Substituting the R1 and R3 example values gives:
R2 = 1/[3.0V/(1.2V x 12k
Ω) - (1/12kΩ) - (1/1.2MΩ)] = 8.05kΩ
In this example, a standard 8.2k
Ω resistor should be used for R2.
6. Verify the trip voltages and hysteresis as:
VTHR = VREF x R1[(1/R1) + (1/R2) + (1/R3)]
(EQ 6)
VTHF = VTHR - (R1 x VCC/R3)(EQ 7)
Hysteresis = VTHR - VTHF
(EQ 8)
OUT
R1
R3
VCC
VIN
VREF
R2
+
VEE
VCC
–
ams
AG
Technical
content
still
valid
相關PDF資料 |
PDF描述 |
|---|---|
| AS3510 | IC CODEC AFE ANALOG 49-CABGA |
| AS3515-T | IC CODEC AFE AUDIO STER 64-CABGA |
| AS3515 | IC CODEC AFE AUDIO STER 64-CABGA |
| AS3517-T | IC CODEC AFE AUDIO STER 81-CTBGA |
| AS3543-ECTP | IC CODEC AUDIO FRONT END 68CTBGA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AS1977 | 制造商:AMSCO 制造商全稱:austriamicrosystems AG 功能描述:Ultra-Low Current, 1.8V Comparators |
| AS1977-T | 功能描述:IC COMPARATOR OPEN SOT23-5 RoHS:是 類別:集成電路 (IC) >> 線性 - 比較器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 類型:通用 元件數:1 輸出類型:CMOS，推挽式，滿擺幅，TTL 電壓 - 電源，單路/雙路(±):2.5 V ~ 5.5 V，±1.25 V ~ 2.75 V 電壓 - 輸入偏移（最小值）:5mV @ 5.5V 電流 - 輸入偏壓（最小值）:1pA @ 5.5V 電流 - 輸出（標準）:- 電流 - 靜態（最大值）:24µA CMRR, PSRR（標準）:80dB CMRR，80dB PSRR 傳輸延遲（最大）:450ns 磁滯:±3mV 工作溫度:-40°C ~ 85°C 封裝/外殼:6-WFBGA，CSPBGA 安裝類型:表面貼裝 包裝:管件 其它名稱:Q3554586 |
| AS197R6FLF | 制造商:TT Electronics / IRC 功能描述:AS197R6FLF |
| AS197R6HLF | 制造商:TT Electronics / IRC 功能描述:AS197R6HLF |
| AS197R6JLF | 制造商:TT Electronics / IRC 功能描述:AS197R6JLF |
發布緊急采購，3分鐘左右您將得到回復。