- 您現在的位置：買賣IC網 > PDF目錄166226 > AP7217C-13SPG-U (DIODES INC) 1.25 V FIXED POSITIVE LDO REGULATOR, PDSO8 PDF資料下載
參數資料
| 型號： | AP7217C-13SPG-U |
| 廠商： | DIODES INC |
| 元件分類： | 固定正電壓?jiǎn)温份敵鯨DO穩壓器 |
| 英文描述： | 1.25 V FIXED POSITIVE LDO REGULATOR, PDSO8 |
| 封裝： | GREEN, SOP-8 |
| 文件頁數： | 7/9頁 |
| 文件大?。?/td> | 190K |
| 代理商： | AP7217C-13SPG-U |
AP7217C
1.25V 600mA CMOS LDO
AP7217C Rev.
1
7 of 9
APRIL 2008
www.diodes.com
Diodes Incorporated
Application Note
Input Capacitor
A 1
μF ceramic capacitor is recommended to connect between IN
and GND pins to decouple input power supply glitch and noise.
The amount of the capacitance may be increased without limit. A
lower ESR (Equivalent Series Resistance) capacitor allows the
use of less capacitance, while higher ESR type requires more
capacitance. This input capacitor must be located as close as
possible to the device to assure input stability and less noise. For
PCB layout, a wide copper trace is required for both IN and GND.
Output Capacitor
The output capacitor is required to stabilize and help the transient
response of the LDO. The AP7217C is designed to have
excellent transient response for most applications with a small
amount of output capacitance. The AP7217C is stable with any
small ceramic output capacitors of 1.0
μF or higher value, and the
temperature coefficients of X7R or X5R type.
Additional
capacitance helps to reduce undershoot and overshoot during
transient. For PCB layout, the output capacitor must be placed as
close as possible to OUT and GND pins, and keep the leads as
short as possible.
ENABLE/SHUTDOWN Operation
The AP7217C (SOP-8L-EP) is turned on by setting the EN pin
high, and is turned off by pulling it low. If this feature is not used,
the EN pin should be tied to IN pin to keep the regulator output on
at all time. To ensure proper operation, the signal source used to
drive the EN pin must be able to swing above and below the
specified turn-on/off voltage thresholds listed in the Electrical
Characteristics section under VIL and VIH.
Thermal Considerations
Thermal
Shutdown
Protection
limits
power
dissipation
in
AP7217C. When the operation junction temperature exceeds
140°C, the Over Temperature Protection circuit starts the thermal
shutdown function and turns the pass element off. The pass
element turn on again after the junction temperature cools by
30°C. For continuous operation, do not exceed absolute
maximum operation junction temperature 125°C. The power
dissipation definition in device is:
PD = (VIN VOUT) x IOUT + VIN x IQ
The maximum power dissipation depends on the thermal
resistance of IC package, PCB layout, the rate of surroundings
airflow and temperature difference between junctions to ambient.
The maximum power dissipation can be calculated by following
formula:
PD(MAX) = ( TJ(MAX) - TA ) / θJA
Where TJ(MAX) is the maximum operation junction temperature
125°C, TA is the ambient temperature and the θJA is the junction
to ambient thermal resistance.
Current Limit Protection
When output current at OUT pin is higher than current limit
threshold, the current limit protection will be triggered and clamp
the
output
current
to
approximately
750mA
to
prevent
over-current and to protect the regulator from damage due to
overheating.
Short circuit protection
When VOUT pin is shorted to GND or VOUT voltage is less than
200mV, short circuit protection will be triggered and clamp the
output current to approximately 70mA.
Vin
Vout
C
Co
ESR
Iin
IN
AP7217C
GND
Iq
OUT
Iout
相關PDF資料 |
PDF描述 |
|---|---|
| AP7S1-FREQ-R-T | CRYSTAL OSCILLATOR, CLOCK, 10 MHz - 166 MHz, HCMOS/TTL OUTPUT |
| AP7S-200MHZ-L-R-T | CRYSTAL OSCILLATOR, CLOCK, 200 MHz, HCMOS/TTL OUTPUT |
| AP7S-10MHZ-N-R | CRYSTAL OSCILLATOR, CLOCK, 10 MHz, HCMOS/TTL OUTPUT |
| AP7S-FREQ-N-T | CRYSTAL OSCILLATOR, CLOCK, 10 MHz - 200 MHz, HCMOS/TTL OUTPUT |
| AP7S1-10MHZ-E-R | CRYSTAL OSCILLATOR, CLOCK, 10 MHz, HCMOS/TTL OUTPUT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AP7217D | 制造商:DIODES 制造商全稱:Diodes Incorporated 功能描述:1.2V 600mA CMOS LDO |
| AP7217D-12YG-13 | 功能描述:低壓差穩壓器 - LDO LDO 600mA 2.5-5.5V 0.8V RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| AP7217-XXS | 制造商:DIODES 制造商全稱:Diodes Incorporated 功能描述:500mA CMOS LDO |
| AP7-23627-1 | 制造商:Sensata Technologies 功能描述:AP7-23627-1 /Pole # 1 /Prod Family: 0202 |
| AP725 100R F | 功能描述:RES SMD 100 OHM 1% 20W TO263 制造商:ohmite 系列:ARCOL，AP725 包裝:托盤 零件狀態:有效 電阻（歐姆）:100 容差:±1% 功率（W）:20W 成分:厚膜 特性:- 溫度系數:±100ppm/°C 工作溫度:-55°C ~ 155°C 封裝/外殼:TO-263-3，D2Pak（2 引線+接片），TO-263AB 供應商器件封裝:TO-263 大小/尺寸:0.398" 長 x 0.177" 寬（10.10mm x 4.50mm） 高度:0.346"（8.80mm） 端子數:2 標準包裝:50 |
發布緊急采購，3分鐘左右您將得到回復。