- 您現在的位置：買賣IC網 > PDF目錄375344 > AP2210K-2.8TRE1 (BCD SEMICONDUCTOR MANUFACTURING LTD) 300mA RF ULDO REGULATOR PDF資料下載
參數資料
| 型號： | AP2210K-2.8TRE1 |
| 廠商： | BCD SEMICONDUCTOR MANUFACTURING LTD |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | 300mA RF ULDO REGULATOR |
| 中文描述： | 2.8 V FIXED POSITIVE LDO REGULATOR, 0.5 V DROPOUT, PDSO5 |
| 封裝： | ROHS COMPLIANT, SOT-23, 5 PIN |
| 文件頁數： | 19/22頁 |
| 文件大小： | 218K |
| 代理商： | AP2210K-2.8TRE1 |
300mA RF ULDO REGULATOR AP2210
Data Sheet
19
Mar. 2007 Rev. 1. 2
BCD Semiconductor Manufacturing Limited
Input Capacitor
A 1
μ
F minimum capacitor is recommended to be
placed between V
IN
and GND.
Output Capacitor
It is required to prevent oscillation. 1.0
μ
F minimum
is recommended when C
BYP
is unused. 2.2
μ
F mini-
mum is recommended when C
BYP
is 100pF. The out-
put capacitor may be increased to improve transient
response.
Noise Bypass Capacitor
Bypass capacitor is connected to the internal voltage
reference. A 100pF capacitor connected from BYP to
GND make this reference quiet, resulting in a
significant reduction in output noise, but the ESR
stable area will be narrowed.
The start-up speed of the AP2210 is inversely
proportional to the value of reference bypass
capacitor. In some cases, if output noise is not a
major concern and rapid turn-on is necessary, omit
C
BYP
and leave BYP open.
Power Dissipation
Thermal shutdown may take place if exceeding the
maximum power dissipation in application. Under all
possible operating conditions, the junction tempera-
ture must be within the range specified under abso-
lute maximum ratings to avoid thermal shutdown.
To determine if the power dissipated in the regulator
reaches the maximum power dissipation (see figure
16, 17), using:
T
J
= P
D
*
θ
JA
+ T
A
P
D
=(V
IN
-V
OUT
)*I
OUT
+V
IN
*I
GND
Where: T
J
≤
T
J(max)
,
T
J(max)
is absolute maximum rat-
ings for the junction temperature; V
IN
*I
GND
can be
ignored due to its small value.
T
J(max)
is 150
o
C
,
θ
JA
is 200
o
C
/W, no heatsink is
required since the package alone will dissipate
enough heat to satisfy these requirements unless the
calculated value for power dissipation exceeds the
limit.
Example (3.0V version):
I
OUT
=300mA, T
A
=50
o
C, V
IN(Max)
is:
(150
o
C
-50
o
C
)/(0.3A*200
o
C/W
)+3.0V=4.67V
Therefore, for good performance, please make sure
that input voltage is less than 4.67V without heatsink
when T
A
=50
o
C.
Application Information
相關PDF資料 |
PDF描述 |
|---|---|
| AP2210K-3.0TR | 300mA RF ULDO REGULATOR |
| AP2210K-3.0TRE1 | 300mA RF ULDO REGULATOR |
| AP2210K-3.3TR | 300mA RF ULDO REGULATOR |
| AP2210K-3.3TRE1 | 300mA RF ULDO REGULATOR |
| AP2210N-2.5TRE1 | 300mA RF ULDO REGULATOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AP2210K-3.0TR | 制造商:BCDSEMI 制造商全稱:BCD Semiconductor Manufacturing Limited 功能描述:300mA RF ULDO REGULATOR |
| AP2210K-3.0TRE1 | 制造商:BCDSEMI 制造商全稱:BCD Semiconductor Manufacturing Limited 功能描述:300mA RF ULDO REGULATOR |
| AP2210K-3.0TRG1 | 制造商:Diodes Incorporated 功能描述:LDO CMOS LOWCURR SOT25 T&R 3K - Tape and Reel 制造商:Diodes Incorporated 功能描述:IC REG LDO 3V 0.3A SOT25 |
| AP2210K-3.3TR | 制造商:BCDSEMI 制造商全稱:BCD Semiconductor Manufacturing Limited 功能描述:300mA RF ULDO REGULATOR |
| AP2210K-3.3TRE1 | 制造商:BCD Semiconductor Manufacturing Ltd 功能描述:300MA ULDO REGULATOR 3.3V SOT-23-5 制造商:Diodes Incorporated 功能描述:LDO CMOS LOWCURR SOT25 T&R 3K - Tape and Reel 制造商:Diodes Incorporated 功能描述:IC REG LDO 3.3V 0.3A SOT25 |
發布緊急采購，3分鐘左右您將得到回復。