- 您現在的位置：買賣IC網 > PDF目錄376492 > AN8783SB (PANASONIC CORP) 4-channel linear driver IC for CD/CD-ROM drive PDF資料下載
參數資料
| 型號： | AN8783SB |
| 廠商： | PANASONIC CORP |
| 元件分類： | 運動控制電子 |
| 英文描述： | 4-channel linear driver IC for CD/CD-ROM drive |
| 中文描述： | DISK DRIVE MOTOR CONTROLLER, 0.5 A, PDSO28 |
| 封裝： | 0.400 INCH, PLASTIC, HSOP-28 |
| 文件頁數： | 5/7頁 |
| 文件大?。?/td> | 57K |
| 代理商： | AN8783SB |
ICs for Compact Disc/CD-ROM Player
AN8783SB
5
Parameter
Symbol
Conditions
Min
Typ
Max
Unit
Thermal protection circuit
Thermal protection operating
temperature
T
THD
160
°
C
Thermal protection hysteresis
width
T
THD
45
°
C
Reset circuit
Voltage detection reset
hysteresis width
V
HYS
0.2
V
I
Electrical Characteristics at SV
CC
=
12 V, V
CC1
=
12 V, V
CC2
=
5 V, R
L
=
8
, V
PC1
=
0 V, V
PC2
=
5 V,
T
a
=
25
°
C (continued)
Design reference data
Note) The characteristics listed below are theoretical values based on the IC design and are not guaranteed.
I
Usage Notes
1. SV
CC
must be used in the highest potential. Otherwise it possibly causes an operation error.
2. Ch. 3 and ch. 4 are current feedback type drivers. Do not apply voltage directly to PVC3 and PVC4, but apply from
PVC2 through the current feedback detection resistors RS3 and RS4 , respectively. And commonly connect S3 pin
to PVC3 pin and S4 pin to PVC4 pin.
At this time, as an output current flows on the detection resistors RS3 and RS4, use a resistor which has a sufficient
allowable power dissipation.
To set gain for ch. 3 and ch. 4, use the following formula:
|
V
IN3(4)
V
REF
|×
2.2 k
=
R
S3(4)
×
I
OUT3(4)
R
3(4)
+
500
(I
OUT3
and I
OUT4
are the load current for ch. 3 and ch. 4, respectively.)
3. Power cut operation
Power cut pins PC1 (for ch. 1, ch. 3, ch. 4) and PC2 (only for ch. 2) are high for mute and low for active.
While ch. 2 is exclusive to a loading motor, ch. 2, ch. 3 and, ch. 4 are driven by the output current from the same
source (PVC2). Therefore, do not use ch. 2 and ch. 3, ch. 4 simultaneously because noise is likely to be put on ch.
3, ch. 4 when ch. 2 is being drived.
4. Appropriate care should be taken on the characteristics.
When changing an external circuit constant on actual use, secure an appropriate margin in consideration of charac-
teristic fluctuation of external parts and our ICs including transient characteristics as well as static ones.
5. Avoid the short-circuits between output pin and V
CC
, output pin and GND (line-to-supply and line-to-ground), and
between output pins (load short-circuit). Otherwise, the IC is likely to emit smoke and break down.
RVC2
RS3
RS4
S3
S4
PVC3
PVC4
相關PDF資料 |
PDF描述 |
|---|---|
| AN8813 | 4-channel driver IC for optical disk drive |
| AN8813NSB | 4-channel driver IC for optical disk drive |
| AN8814 | 4-channel driver IC for optical disk drive |
| AN8814SB | 4-channel driver IC for optical disk drive |
| AN8816 | 4ch. Linear Driver IC for CD/CD-ROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AN8787 | 制造商:PANASONIC 制造商全稱:Panasonic Semiconductor 功能描述:4-channel linear driver IC for CD/CD-ROM drive |
| AN8787NSB | 制造商:PANASONIC 制造商全稱:Panasonic Semiconductor 功能描述:4-channel linear driver IC for CD/CD-ROM drive |
| AN8788FB | 制造商:Panasonic Industrial Company 功能描述:IC |
| AN8796 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
| AN8796C | 制造商:Analog Devices 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。