- 您現在的位置：買賣IC網 > PDF目錄376490 > AN7199Z (PANASONIC CORP) Dual 20 W BTL power IC for car audio PDF資料下載
參數資料
| 型號： | AN7199Z |
| 廠商： | PANASONIC CORP |
| 元件分類： | 音頻／視頻放大 |
| 英文描述： | Dual 20 W BTL power IC for car audio |
| 中文描述： | 25 W, 2 CHANNEL, AUDIO AMPLIFIER, PZFM15 |
| 封裝： | ZFM-15 |
| 文件頁數： | 13/17頁 |
| 文件大?。?/td> | 131K |
| 代理商： | AN7199Z |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁
ICs for Audio Common Use
AN7199Z
13
I
Technical Information (continued)
[2] Application note (continued)
4. Ripple filter (continued)
6) After the power supply is
turned off (STB-low), it takes
less than 10 seconds for the
total circuit current to become
the standby current (under 10
μ
A). If approx. 47 ohms resis-
tor is inserted between the
ripple filter terminal and GND
for the purpose of reducing
the inspection time with set, a
time until the current becomes
the standby current can be
shortened.
5. GND terminal
1) Be sure to short-circuit each GND terminal of
pin 3, 8, 9 and 14 at the outside of the IC in use.
2) For each GND terminal, the one-point earth,
referenced to the GND connection point of
electrolytic capacitor between the supply ter-
minal and GND, is most effective for reduc-
ing the distortion. Even in the worst case,
ground pin 8, 9 of input GND separately from
all the other GND terminals.
3) Each GND terminal is not electrically short-circuited inside. Only pin 8 is connected with substrate.
4) Pin 9 is input signal GND. Connect only pin 9 with Pre-GND.
6. Cooling fin
1) The cooling fin is not connected with GND terminal by using Au wire. Only pin 8 is electrically connected
through substrate.
2) Always attach an outside heat sink to the cooling fin. The cooling fin must be fastened onto a chassis for use.
Otherwise, IC lead failure may occur.
3) Do not give the cooling fin any potential other than the GND potential. Otherwise, it may cause breakdown.
4) Connection of the cooling fin with GND can reduce the incoming noise hum. (It is unnecessary to connect
with GND in use, but connect with the power GND when the cooling fin is connected with GND)
7. Shock noise
1) STB on/off
No shock noise is released. However, the changeover switch of the standby terminal may make a slight
shock noise. In such a case, insert a capacitor of approx. 0.01
μ
F between the standby terminal and GND.
2) Mute on/off
No shock noise is released. Refer to the section on the mute function.
1
3
8
9
14
To GND of input
AN7198Z, AN7199Z
Figure 6
350
μ
A
33
μ
F
12
10 k
4 k
10 k
15 k
V
REF
V
CC
1.7 mA
Constant
current source
Protection
circuit
Figure 5
相關PDF資料 |
PDF描述 |
|---|---|
| AN7205 | FM FRONT-END CIRCUIT FOR RADIOS AND RADIO / CASSETTE TAPE RECORDERS (3V OPERATION) |
| AN7205S | FM FRONT-END CIRCUIT FOR RADIOS AND RADIO / CASSETTE TAPE RECORDERS (3V OPERATION) |
| AN7216 | FM FRONT END CIRCUIT FOR RADIOS |
| AN7216S | FM FRONT END CIRCUIT FOR RADIOS |
| AN7223 | AM Tuner, FM/AM IF Amplifier Circuit for Radio Cassette Recorder |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AN720 | 制造商:SILABS 制造商全稱:SILABS 功能描述:PRECISION32a?￠ OPTIMIZATION CONSIDERATIONS FOR CODE SIZE AND SPEED |
| AN7203 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:FM FRONT-END IC FOR RADIO, RADIO CASSETTE RECORDER |
| AN7204 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:FM Receiver Circuit |
| AN7205 | 制造商:Panasonic Industrial Company 功能描述:IC |
| AN7205S | 制造商:PANASONIC 制造商全稱:Panasonic Semiconductor 功能描述:FM FRONT-END CIRCUIT FOR RADIOS AND RADIO / CASSETTE TAPE RECORDERS (3V OPERATION) |
發布緊急采購，3分鐘左右您將得到回復。