- 您現在的位置：買賣IC網 > PDF目錄376490 > AN7195K (PANASONIC CORP) Dual 15 W BTL power IC for car audio PDF資料下載
參數資料
| 型號： | AN7195K |
| 廠商： | PANASONIC CORP |
| 元件分類： | 音頻／視頻放大 |
| 英文描述： | Dual 15 W BTL power IC for car audio |
| 中文描述： | 20 W, 2 CHANNEL, AUDIO AMPLIFIER, PZFM16 |
| 封裝： | HZIP-16 |
| 文件頁數： | 8/12頁 |
| 文件大?。?/td> | 102K |
| 代理商： | AN7195K |
AN7195K
ICs for Audio Common Use
8
I
Technical Information (continued)
[2] Application note (continued)
2. Oscillation countermeasures
1) In order to increase the oscillation allowance, connect a capacitor and
a resistor in series between each output terminal and GND as shown
in figure 2.
2) The use of polyester film capacitor having a little fluctuation with
temperature and frequency is recommended as the 0.1
μ
F capacitor
for oscillation prevention.
3. Input terminal
1) The reference voltage of input terminal is 0 V. When the input signal has a reference voltage other than 0 V
potential, connect a coupling capacitor (of about several
μ
F) for DC component cut in series with the input
terminal. Check the low-pass frequency characteristics to determine the capacitor value.
2) 10 k
or less of signal source impedance R
g
can reduce the output end noise voltage.
3) The output offset voltage fluctuates when the signal source impedance R
g
is changed. A care must be taken
when using the circuit by directly connecting the volume to the input terminal. In such a case, the use of
coupling capacitor is recommended.
4) If a high frequency signal from tuners enters the input terminal as noise, insert a capacitor of approx. 0.01
μ
F
between the input terminal and input GND.
When a high frequency signal is inputted, malfunction in protective circuits may occur.
Figure 3
4. Ripple filter
1) In order to suppress the fluctuation of supply voltage, connect a capacitor of approx. 33
μ
F between RF
terminal (pin12) and GND.
2) Relation between RR (Ripple Rejection Ratio) and a capacitor
The larger the capacitance of the ripple filter is, the better the ripple rejection becomes.
3) Relation between the rise time of circuit and a capacitor
The larger the capacitance of the ripple filter is, the longer the time from the power on (standby high) to the
sound release becomes.
4) The DC voltage of output terminal is approximately the middle point of the ripple filter terminal voltage.
5) The internal circuit of ripple filter terminal is as shown in figure 4 and the charge current is approx. 3 mA to
10 mA.
6) The muting circuit turns on when the ripple filter terminal is V
CC
4 V
BE
or less.
For that reason, abnormal sound due to waveform distortion at rising and falling of the circuit is not released.
4.7 k
30 k
200
6
11
400
15
μ
A
0.01
μ
F
1
μ
F
15
μ
A
Attenuator
To power
Input signal
2.2
0.1
μ
F
2,4
1
13,15
3,14
To speaker
Figure 2
相關PDF資料 |
PDF描述 |
|---|---|
| AN7195Z | Dual 15 W BTL power IC for car audio |
| AN7196 | 16 A SPDT MINIATURE POWER RELAY |
| AN7196K | Dual 15 W BTL power IC for car audio |
| AN7196Z | Dual 15 W BTL power IC for car audio |
| AN7199 | Dual 20 W BTL power IC for car audio |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AN7195Z | 制造商:PANASONIC 制造商全稱:Panasonic Semiconductor 功能描述:Dual 15 W BTL power IC for car audio |
| AN7196 | 制造商:PANASONIC 制造商全稱:Panasonic Semiconductor 功能描述:Dual 15 W BTL power IC for car audio |
| AN7196K | 制造商:PANASONIC 制造商全稱:Panasonic Semiconductor 功能描述:Dual 15 W BTL power IC for car audio |
| AN7196Z | 制造商:PANASONIC 制造商全稱:Panasonic Semiconductor 功能描述:Dual 15 W BTL power IC for car audio |
| AN7198Z | 制造商:PANASONIC 制造商全稱:Panasonic Semiconductor 功能描述:Dual 20 W BTL Power IC for Car Audio |
發布緊急采購，3分鐘左右您將得到回復。