- 您現在的位置：買賣IC網 > PDF目錄366551 > AM79C984 (Advanced Micro Devices, Inc.) enhanced Integrated Multiport Repeater (eIMR⑩) PDF資料下載
參數資料
| 型號： | AM79C984 |
| 廠商： | Advanced Micro Devices, Inc. |
| 英文描述： | enhanced Integrated Multiport Repeater (eIMR⑩) |
| 中文描述： | 強化的綜合多端中繼器（eIMR⑩） |
| 文件頁數： | 26/44頁 |
| 文件大?。?/td> | 222K |
| 代理商： | AM79C984 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
P R E L I M I N A R Y
26
Am79C984A
Enable Software Override of Bank B LEDs (Per Port -
AUI and TP Global)
SI Data
1100 ####
SO Data
None
This command forces the LEDs in Bank B to blink. In-
dividual LEDs and combinations of LEDs can be select-
ed via the lower four bits of the command byte as follows:
####
0000-0011 TP0 - TP3
0100-0111 Reserved
1000
1001
1010
1011
1100
1101
1110
1111
Port(s) affected
AUI port
Reserved
Reserved
All TP ports
All ports
Global
Reserved
Reserved
The designated LED driver(s) will switch between LOW
and ‘off’ at the rate set by the Software Override of LED
Blink Rate command. Enable Software Override of
Bank B LEDs references the blink rate last issued and
overrides any other attribute specified by LDC
ware Override of LEDs is disabled after reset.
0-2
. Soft-
Software Override of LED Blink Rate
SI Data
SO Data
1110 1###
None
This command sets the blink period of the LEDs with
Software Override enabled. The duty cycle is 50%. This
command defaults to ‘off’ at reset.
Setting
1110 1000
1110 1001
1110 1010
1110 1011
Blink Period
Off
512 ms
1560 ms
Solid On
These settings apply to the blink rate for both Bank A
and Bank B. This command must precede the Enable
Software Override of Bank A/B LEDs command. All LED
combinations selected for Software Override will refer-
ence the blink rate last issued.
GET (Read Commands)
AUI Port(s) Status
SI Data
SO Data
1000 1111
PBSL 0000
The combined AUI status of the eIMR device allows a
single instruction to be used to monitor the AUI port.
The four local status bits are:
P
Partitioning Status
This bit is ‘0’ if the AUI port is partitioned and ‘1’ if the
AUI port is connected.
B
Bit Rate Error
This bit is set to 1’ if there is an instance of FIFO overflow
or underflow. The bit is cleared when the eIMR device
is read.
S
SQE Test Status
This bit is set to ‘1’ if the SQE test error is detected by
the eIMR chip. The bit is cleared when the status is read.
L
Loopback Error
The MAU attached to the AUI port is required to loop-
back data transmitted to DO onto the DI circuit. If the
loopback carrier is not detected by the eIMR device, this
bit is set to ‘1’. This bit is cleared when the status is read.
Alternate AUI Port(s) Status
There are three further variations of the AUI Port Status
Command allowing selective clearing of a combination
of B,S, and L bits. These are the following:
Alternate 1: B is not cleared, S and L are Cleared
SI Data
SO Data
1000 1011
PBSL 0000
Alternate 2: S and L are not cleared, B is Cleared
SI Data
SO Data
1000 1101
PBSL 0000
Alternate 3: None of S, B, and L are Cleared
SI Data
SO Data
1000 1001
PBSL 0000
TP Port Partitioning Status
SI Data
SO Data
1000 0000
0000 P3..P0
P
P
n
n
= 0
= 1
TP Port Partitioned
TP port Connected
where
n
is a port number in the range 0–3.
The response to this command gives the partitioning
status of all four TP ports. If a port is disabled, reading
its partitioning status will indicate that it is connected.
Bit Rate Error Status of TP Ports
SI Data
SO Data
1010 0000
0000 E3..E0
E
E
n
n
n
= 0
= 1
is a port number in the range 0–3.
No Error
FIFO Overflow
where
The response to this command gives the bit-rate-over-
flow or underflow (data rate mismatch) condition of all
the TP ports. A 1 indicates that the FIFO has overflowed
or underflowed due to the amount of data received by
the corresponding port.
相關PDF資料 |
PDF描述 |
|---|---|
| AM79C984A | enhanced Integrated Multiport Repeater (eIMR⑩) |
| AM79C984AJC | enhanced Integrated Multiport Repeater (eIMR⑩) |
| AM79C984AKCW | Circular Connector; No. of Contacts:6; Series:MS27474; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:8; Circular Contact Gender:Pin; Circular Shell Style:Jam Nut Receptacle; Insert Arrangement:8-35 RoHS Compliant: No |
| AM79C985JC | enhanced Integrated Multiport Repeater Plus (eIMR+⑩) |
| AM79C985 | enhanced Integrated Multiport Repeater Plus (eIMR+⑩) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AM79C984A | 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:enhanced Integrated Multiport Repeater (eIMR⑩) |
| AM79C984AJC | 制造商:Advanced Micro Devices 功能描述:AM79C984AJC - Bulk 制造商:Rochester Electronics LLC 功能描述: |
| AM79C984AKC\\W | 制造商:Advanced Micro Devices 功能描述: 制造商:Rochester Electronics LLC 功能描述: |
| AM79C984AKC\W | 制造商:Advanced Micro Devices 功能描述: 制造商:Rochester Electronics LLC 功能描述: |
| AM79C984AKCW | 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:enhanced Integrated Multiport Repeater (eIMR⑩) |
發布緊急采購，3分鐘左右您將得到回復。