參數資料
型號： AM79C961AKCW
廠商： ADVANCED MICRO DEVICES INC
元件分類： 微控制器/微處理器
英文描述： PCnet ⑩-ISA II Jumperless, Full Duplex Single-Chip Ethernet Controller for ISA
中文描述： 2 CHANNEL(S), 10M bps, LOCAL AREA NETWORK CONTROLLER, PQFP132
封裝： PLASTIC, QFP-132
文件頁數： 64/85頁
文件大小： 1088K
代理商： AM79C961AKCW
64
Am79C961A
P R E L I M I N A R Y
larger than the 4
μ
s blinding window, then the IPG
counter will be reset by a worst case IPG shrinkage/
fragment scenario and the PCnet-ISA II controller will
defer its transmission. In addition, the PCnet-ISA II
controller will not restart the “blinding” period if carrier
is detected within the 4.0
μ
s – 6.0
μ
s IFS1 period, but
will commence timing of the entire IFS1 period.
Contention resolution (collision handling)
Collision detection is performed and reported to the
MAC engine by the integrated Manchester Encoder/
Decoder (MENDEC).
If a collision is detected before the complete preamble/
SFD sequence has been transmitted, the MAC Engine
will complete the preamble/SFD before appending the
jam sequence. If a collision is detected after the pream-
ble/SFD has been completed, but prior to 512 bits
being transmitted, the MAC Engine will abort the trans-
mission, and append the jam sequence immediately.
The jam sequence is a 32-bit all zeroes pattern.
The MAC Engine will attempt to transmit a frame a total
of 16 times (initial attempt plus 15 retries) due to nor-
mal collisions (those within the slot time). Detection of
collision will cause the transmission to be
re-scheduled, dependent on the backoff time that the
MAC Engine computes. If a single retry was required,
the ONE bit will be set in the Transmit Frame Status
(TMD1 in the Transmit Descriptor Ring). If more than
one retry was required, the MORE bit will be set. If all
16 attempts experienced collisions, the RTRY bit (in
TMD2) will be set (ONE and MORE will be clear), and
the transmit message will be flushed from the FIFO. If
retries have been disabled by setting the DRTY bit in
the MODE register (CSR15), the MAC Engine will
abandon transmission of the frame on detection of the
first collision. In this case, only the RTRY bit will be set
and the transmit message will be flushed from the
FIFO.
If a collision is detected after 512 bit times have been
transmitted, the collision is termed a late collision. The
MAC Engine will abort the transmission, append the
jam sequence, and set the LCOL bit. No retry attempt
will be scheduled on detection of a late collision, and
the FIFO will be flushed.
The IEEE 802.3 Standard requires use of a “truncated
binary exponential backoff” algorithm which provides a
controlled pseudo-random mechanism to enforce the
collision backoff interval, before re-transmission is
attempted.
See ANSI/IEEE Std 802.3-1990 Edition, 4.2.3.2.5:
“At the end of enforcing a collision (jamming),
the CSMA/CD sublayer delays before attempt-
ing to re-transmit the frame. The delay is an in-
teger multiple of slot Time. The number of slot
times to delay before the nth re-transmission
attempt is chosen as a uniformly distributed
random integer r in the range:
0
≤
r < 2
k
, where k = min (n,10).”
The PCnet-ISA II controller provides an alternative
algorithm, which suspends the counting of the slot
time/IPG during the time that receive carrier sense is
detected. This algorithm aids in networks where large
numbers of nodes are present, and numerous nodes
can be in collision. The algorithm effectively acceler-
ates the increase in the backoff time in busy networks,
and allows nodes not involved in the collision to access
the channel while the colliding nodes await a reduction
in channel activity. Once channel activity is reduced,
the nodes resolving the collision time out their slot time
counters as normal.
Manchester Encoder/Decoder (MENDEC)
The integrated Manchester Encoder/Decoder provides
the PLS (Physical Layer Signaling) functions required
for a fully compliant IEEE 802.3 station. The MENDEC
provides the encoding function for data to be transmit-
ted on the network using the high accuracy on-board
oscillator, driven by either the crystal oscillator or an ex-
ternal CMOS-level compatible clock. The MENDEC
also provides the decoding function from data received
from the network. The MENDEC contains a Power On
Reset (POR) circuit, which ensures that all analog por-
tions of the PCnet-ISA II controller are forced into their
correct state during power-up, and prevents erroneous
data transmission and/or reception during this time.
External Crystal Characteristics
When using a crystal to drive the oscillator, the crystal
specification shown in the specification table may be
used to ensure less than
±
0.5 ns jitter at DO
±
.
External Crystal Characteristics
Requires trimming crystal spec; no trim is 50 ppm total
Parameter
Min
Nom
Max
Unit
1. Parallel Resonant Frequency
20
MHz
2. Resonant Frequency Error
(CL = 20 pF)
–50
+50
PPM
3.Change in Resonant
Frequency With Respect
To Temperature
(0
°
– 70
°
C; CL = 20 pF)*
–40
+40
PPM
4. Crystal Capacitance
20
pF
5. Motional Crystal Capacitance
(C1)
0.022
pF
6. Series Resistance
25
7. Shunt Capacitance
7
pF
8. Drive Level
TBD
mW
相關PDF資料
PDF描述
AM79C961AKC PCnet ⑩-ISA II Jumperless, Full Duplex Single-Chip Ethernet Controller for ISA
AM79C961A PCnet ⑩-ISA II Jumperless, Full Duplex Single-Chip Ethernet Controller for ISA
AM79C961AKIW PCnet⑩-ISA II Jumperless, Full Duplex Single-Chip Ethernet Controller for ISA
AM79C961AVCW PCnet⑩-ISA II Jumperless, Full Duplex Single-Chip Ethernet Controller for ISA
AM79C961AVIW PCnet⑩-ISA II Jumperless, Full Duplex Single-Chip Ethernet Controller for ISA
相關代理商/技術參數
參數描述
AM79C961AKI 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LAN Node Controller
AM79C961AKI/W 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LAN Node Controller
AM79C961AKIW 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:PCnet⑩-ISA II Jumperless, Full Duplex Single-Chip Ethernet Controller for ISA
AM79C961APDLUTS 制造商:Advanced Micro Devices 功能描述:
AM79C961AVC 制造商:Rochester Electronics LLC 功能描述: 制造商:Advanced Micro Devices 功能描述:LAN Node Controller, 144 Pin, TQFP
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*