- 您現在的位置：買賣IC網 > PDF目錄366550 > AM79C960KC (ADVANCED MICRO DEVICES INC) PCnetTM-ISA Single-Chip Ethernet Controller PDF資料下載
參數資料
| 型號： | AM79C960KC |
| 廠商： | ADVANCED MICRO DEVICES INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | PCnetTM-ISA Single-Chip Ethernet Controller |
| 中文描述： | 2 CHANNEL(S), 10M bps, LOCAL AREA NETWORK CONTROLLER, PQFP120 |
| 封裝： | CARRIER RING, PLASTIC, QFP-120 |
| 文件頁數： | 44/127頁 |
| 文件大?。?/td> | 814K |
| 代理商： | AM79C960KC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁當前第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁
P R E L I M I N A R Y
AMD
1-386
Am79C960
Negative link beat pulses are defined as transmitted sig-
nals with a negative amplitude greater than 585 mV with
a pulse width of 60 ns–200 ns. This negative excursion
may be followed by a positive excursion. This definition
is consistent with the expected received signal at a re-
verse wired receiver, when a link beat pulse which fits
the template of Figure 14–12 in the 10BASE-T Standard
is generated at a transmitter and passed through 100 m
of twisted pair cable.
The polarity detection/correction algorithm will remain
“armed” until two consecutive packets with valid ETD of
identical polarity are detected. When “armed,” the re-
ceiver is capable of changing the initial or previous
polarity configuration according to the detected ETD
polarity.
On receipt of the first packet with valid ETD following re-
set or Link Fail, the T-MAU will use the inferred polarity
information to configure its RXD
±
input, regardless of its
previous state. On receipt of a second packet with a
valid ETD with correct polarity, the detection/correction
algorithm will “l(fā)ock-in” the received polarity. If the sec-
ond (or subsequent) packet is not detected as
confirming the previous polarity decision, the most re-
cently detected ETD polarity will be used as the default.
Note that packets with invalid ETD have no effect on up-
dating the previous polarity decision. Once two
consecutive packets with valid ETD have been re-
ceived, the T-MAU will lock the correction algorithm until
either a Link Fail condition occurs or RESET is asserted.
During polarity reversal, an internal POL signal will be
active. During normal polarity conditions, this internal
POL signal is inactive. The state of this signal can be
read by software and/or displayed by LED when en-
abled by the LED control bits in the ISA Bus
Configuration Registers (ISACSR5, 6, 7).
Twisted Pair Interface Status
Three signals (XMT, RCV and COL) indicate whether
the T-MAU is transmitting, receiving, or in a collision
state. These signals are internal signals and the behav-
ior of the LED outputs depends on how the LED output
circuitry is programmed.
The T-MAU will power up in the Link Fail state and the
normal algorithm will apply to allow it to enter the Link
Pass state. In the Link Pass state, transmit or receive
activity will be indicated by assertion of RCV signal go-
ing active. If T-MAU is selected using the PORTSEL bits
in CSR15 or MAUSEL pin, then when moving from AUI
to T-MAU selection the T-MAU will be forced into the
Link Fail state.
In the Link Fail state, XMT, RCV and COL are inactive.
Collision Detect Function
Activity on both twisted pair signals RXD
±
and TXD
±
constitutes a collision, thereby causing the COL signal
to be asserted. (COL is used by the LED control cir-
cuits.) The COL will remain asserted until one of the two
colliding signals changes from active to idle. During col-
lision condition, data presented on the DI
±
pair will be
sourced from the RXD
±
input. COL stays active for two
bit times at the end of a collision.
Signal Quality Error (SQE) Test
(Heartbeat) Function
The SQE function is disabled when the 10BASE-T port
is selected and in Link Fail state.
Jabber Function
The Jabber function inhibits the twisted pair transmit
function of the T-MAU if theTXD
±
circuit is active for an
excessive period (20–150 ms). This prevents any one
node from disrupting the network due to a ‘stuck-on’ or
faulty transmitter. If this maximum transmit time is ex-
ceeded, the T-MAU transmitter circuitry is disabled, the
JAB bit is set (CSR4, bit 1), and COL signal asserted.
Once the transmit data stream to the T-MAU is re-
moved, an “unjab” time of 250–750 ms will elapse
before the T-MAU deasserts COL and re-enables the
transmit circuitry.
Power Down
The T-MAU circuitry can be made to go into low power
mode. This feature is useful in battery powered or low
duty cycle systems. The T-MAU will go into power down
mode when RESET is active,
coma mode
is active, or
the T-MAU is not selected. Refer to the Power Down
Mode section for a description of the various power
down modes.
Any of the three conditions listed above resets the inter-
nal logic of the T-MAU and places the device into power
down mode. In this mode, the Twisted Pair driver pins
(TXD
±
,TXP
±
) are asserted LOW, and the internal T-
MAU status signals (LNKST, RCVPOL, XMT, RCV and
COLLISION) are inactive.
Once the
SLEEP
pin is deasserted, the T-MAU will be
forced into the Link Fail state. The T-MAU will move to
the Link Pass state only after 5 - 6 link beat pulses and/or
a single received message is detected on the RXD
±
pair.
In
snooze
mode, the T-MAU receive circuitry will remain
enabled even while the
SLEEP
pin is driven LOW.
The T-MAU circuitry will always go into power down
mode if RESET is asserted,
coma mode
is enabled, or
the T-MAU is not selected.
相關PDF資料 |
PDF描述 |
|---|---|
| AM79C960KCW | PCnetTM-ISA Single-Chip Ethernet Controller |
| AM79C961AKCW | PCnet ⑩-ISA II Jumperless, Full Duplex Single-Chip Ethernet Controller for ISA |
| AM79C961AKC | PCnet ⑩-ISA II Jumperless, Full Duplex Single-Chip Ethernet Controller for ISA |
| AM79C961A | PCnet ⑩-ISA II Jumperless, Full Duplex Single-Chip Ethernet Controller for ISA |
| AM79C961AKIW | PCnet⑩-ISA II Jumperless, Full Duplex Single-Chip Ethernet Controller for ISA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AM79C960KC/W | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LAN Node Controller |
| AM79C960KCW | 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:PCnetTM-ISA Single-Chip Ethernet Controller |
| AM79C961 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Am79C961 - PCnet-ISA+ Jumperless Single-Chip Ethernet Controller for ISA |
| AM79C961/AM79C961A | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Using the Am79C961/Am79C961A (PCnet-ISA+/PCnet-ISA II) Survival Guide? 134KB (PDF) |
發布緊急采購，3分鐘左右您將得到回復。