- 您現在的位置：買賣IC網 > PDF目錄366549 > AM79C873KCW (ADVANCED MICRO DEVICES INC) NetPHY⑩ -1 10/100 Mbps Ethernet Physical Layer Single-Chip Transceiver with 100BASE-FX Support PDF資料下載
參數資料
| 型號： | AM79C873KCW |
| 廠商： | ADVANCED MICRO DEVICES INC |
| 元件分類： | 網絡接口 |
| 英文描述： | NetPHY⑩ -1 10/100 Mbps Ethernet Physical Layer Single-Chip Transceiver with 100BASE-FX Support |
| 中文描述： | DATACOM, ETHERNET TRANSCEIVER, PQFP100 |
| 封裝： | PLASTIC, QFP-100 |
| 文件頁數： | 22/44頁 |
| 文件大小： | 543K |
| 代理商： | AM79C873KCW |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
22
Am79C873
P R E L I M I N A R Y
Basic Mode Status Register (BMSR) -
Register 1
Bit
Bit Name
Default
Description
1.15
100BASE-T4
0,RO/P
100BASE-T4 Capable
:
1=NetPHY-1 device is able to perform in 100BASE-T4 mode.
0=NetPHY-1 device is not able to perform in 100BASE-T4 mode.
1.14
100BASE-TX
Full Duplex
1,RO/P
100BASE-TX Full Duplex Capable
:
1=NetPHY-1 device is able to perform 100BASE-TX in Full Duplex mode.
0=NetPHY-1 device is not able to perform 100BASE-TX in Full Duplex
mode.
1.13
100BASE-TX
Half Duplex
1,RO/P
100BASE-TX Half Duplex Capable
:
1=NetPHY-1 device is able to perform 100BASE-TX in Half Duplex mode.
0=NetPHY-1 device is not able to perform 100BASE-TX in Half Duplex
mode.
1.12
10BASE-T
Full Duplex
1,RO/P
10BASE-T Full Duplex Capable
:
1=NetPHY-1 device is able to perform 10BASE-T in Full Duplex mode.
0=NetPHY-1 device is not able to perform 10BASE-T in Full Duplex mode.
1.11
10BASE-T
Half Duplex
1,RO/P
10BASE-T Half Duplex Capable
:
1=NetPHY-1 device is able to perform 10BASE-T in Half Duplex mode.
0=NetPHY-1 device is not able to perform 10BASE-T in Half Duplex mode.
1.10-1.7
Reserved
0,RO
Reserved
:
Write as 0, ignore on read.
1.6
MF Preamble
Suppression
0,RO
MII Frame Preamble Suppression
:
1=PHY will accept management frames with preamble suppressed.
0=PHY will not accept management frames with preamble suppressed.
1.5
Auto-Negotiation
Complete
0,RO
Auto-Negotiation Complete
:
1=Auto-Negotiation process completed.
0=Auto-Negotiation process not completed.
1.4
Remote Fault
0,
RO/LH
Remote Fault
:
1= Remote fault condition detected (cleared on read or by a chip reset).
Fault criteria and detection method is NetPHY-1 device implementation
specific. This bit will set after the RF bit in the ANLPAR (bit 13, register
address 05) is set.
0= No remote fault condition detected.
1.3
Auto-Negotiation
Ability
1,RO/P
Auto Configuration Ability
:
1=NetPHY-1 device able to perform Auto-Negotiation.
0=NetPHY-1 device not able to perform Auto-Negotiation.
1.2
Link Status
0,RO/LL
Link Status
:
1=Valid link established (for either 10 Mbps or 100 Mbps operation).
0=Link not established.
The link status bit is implemented with a latching function, so that the
occurrence of a link failure condition causes the Link Status bit to be
cleared and remain cleared until it is read via the management interface.
相關PDF資料 |
PDF描述 |
|---|---|
| AM79C874VI | NetPHY-1LP Low Power 10/100-TX/FX Ethernet Transceiver |
| Am79C874 | NetPHY-1LP Low Power 10/100-TX/FX Ethernet Transceiver |
| AM79C874VC | NetPHY-1LP Low Power 10/100-TX/FX Ethernet Transceiver |
| AM79C875 | NetPHY⑩ 4LP Low Power Quad 10/100-TX/FX Ethernet Transceiver |
| AM79C875KC | NetPHY⑩ 4LP Low Power Quad 10/100-TX/FX Ethernet Transceiver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AM79C874 | 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:NetPHY-1LP Low Power 10/100-TX/FX Ethernet Transceiver |
| AM79C874KC/W | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LAN Transceiver |
| AM79C874VC | 制造商:Advanced Micro Devices 功能描述:PHY 1-CH 10Mbps/100Mbps 80-Pin TQFP 制造商:AMD (Advanced Micro Devices) 功能描述:PHY 1-CH 10Mbps/100Mbps 80-Pin TQFP |
| AM79C874VD | 制造商:Advanced Micro Devices 功能描述:PHY 1-CH 10Mbps/100Mbps 80-Pin TQFP 制造商:AMD (Advanced Micro Devices) 功能描述:PHY 1-CH 10Mbps/100Mbps 80-Pin TQFP |
發布緊急采購，3分鐘左右您將得到回復。