<kbd id="n8k3l"><label id="n8k3l"><dl id="n8k3l"></dl></label></kbd>
<kbd id="n8k3l"><label id="n8k3l"></label></kbd>
<nobr id="n8k3l"><strike id="n8k3l"></strike></nobr>
<center id="n8k3l"></center>
<center id="n8k3l"><dfn id="n8k3l"><label id="n8k3l"></label></dfn></center>
<nobr id="n8k3l"></nobr>
  • <small id="n8k3l"></small>
    參數資料
    型號: AM29LV640MH90RPCI
    廠商: ADVANCED MICRO DEVICES INC
    元件分類: PROM
    英文描述: 64 Megabit (4 M x 16-Bit/8 M x 8-Bit) MirrorBit⑩ 3.0 Volt-only Uniform Sector Flash Memory with VersatileI/O⑩ Control
    中文描述: 4M X 16 FLASH 3V PROM, 90 ns, PBGA64
    封裝: 13 X 11 MM, 1 MM PITCH, BGA-64
    文件頁數: 37/62頁
    文件大小: 602K
    代理商: AM29LV640MH90RPCI
    December 14, 2005
    Am29LV640MH/L
    35
    D A T A S H E E T
    WRITE OPERATION STATUS
    The device provides several bits to determine the sta-
    tus of a program or erase operation: DQ2, DQ3, DQ5,
    DQ6, and DQ7.
    Table 12
    and the following subsec-
    tions describe the function of these bits. DQ7 and DQ6
    each offer a method for determining whether a pro-
    gram or erase operation is complete or in progress.
    The device also provides a hardware-based output
    signal, RY/BY#, to determine whether an Embedded
    Program or Erase operation is in progress or has been
    completed.
    DQ7: Data# Polling
    The Data# Polling bit, DQ7, indicates to the host sys-
    tem whether an Embedded Program or Erase algo-
    rithm is in progress or completed, or whether the
    device is in Erase Suspend. Data# Polling is valid after
    the rising edge of the final WE# pulse in the command
    sequence.
    During the Embedded Program algorithm, the device
    outputs on DQ7 the complement of the datum pro-
    grammed to DQ7. This DQ7 status also applies to pro-
    gramming during Erase Suspend. When the
    Embedded Program algorithm is complete, the device
    outputs the datum programmed to DQ7. The system
    must provide the program address to read valid status
    information on DQ7. If a program address falls within a
    protected sector, Data# Polling on DQ7 is active for
    approximately 1 μs, then the device returns to the read
    mode.
    During the Embedded Erase algorithm, Data# Polling
    produces a “0” on DQ7. When the Embedded Erase
    algorithm is complete, or if the device enters the Erase
    Suspend mode, Data# Polling produces a “1” on DQ7.
    The system must provide an address within any of the
    sectors selected for erasure to read valid status infor-
    mation on DQ7.
    After an erase command sequence is written, if all
    sectors selected for erasing are protected, Data# Poll-
    ing on DQ7 is active for approximately 100 μs, then the
    device returns to the read mode. If not all selected
    sectors are protected, the Embedded Erase algorithm
    erases the unprotected sectors, and ignores the se-
    lected sectors that are protected. However, if the sys-
    tem reads DQ7 at an address within a protected
    sector, the status may not be valid.
    Just prior to the completion of an Embedded Program
    or Erase operation, DQ7 may change asynchronously
    with DQ0–DQ6 while Output Enable (OE#) is asserted
    low. That is, the device may change from providing
    status information to valid data on DQ7. Depending on
    when the system samples the DQ7 output, it may read
    the status or valid data. Even if the device has com-
    pleted the program or erase operation and DQ7 has
    valid data, the data outputs on DQ0–DQ6 may be still
    invalid. Valid data on DQ0–DQ7 will appear on suc-
    cessive read cycles.
    Table 12
    shows the outputs for Data# Polling on DQ7.
    Figure 8 shows the Data# Polling algorithm. Figure 20
    in the
    AC Characteristics
    section shows the Data#
    Polling timing diagram.
    相關PDF資料
    PDF描述
    AM29LV640ML 64 Megabit (4 M x 16-Bit/8 M x 8-Bit) MirrorBit⑩ 3.0 Volt-only Uniform Sector Flash Memory with VersatileI/O⑩ Control
    AM29LV640ML101EI 64 Megabit (4 M x 16-Bit/8 M x 8-Bit) MirrorBit⑩ 3.0 Volt-only Uniform Sector Flash Memory with VersatileI/O⑩ Control
    AM29LV640ML101FI 64 Megabit (4 M x 16-Bit/8 M x 8-Bit) MirrorBit⑩ 3.0 Volt-only Uniform Sector Flash Memory with VersatileI/O⑩ Control
    AM29LV640ML101PCI 64 Megabit (4 M x 16-Bit/8 M x 8-Bit) MirrorBit⑩ 3.0 Volt-only Uniform Sector Flash Memory with VersatileI/O⑩ Control
    AM29LV640ML101REI 64 Megabit (4 M x 16-Bit/8 M x 8-Bit) MirrorBit⑩ 3.0 Volt-only Uniform Sector Flash Memory with VersatileI/O⑩ Control
    相關代理商/技術參數
    參數描述
    AM29LV640MU101RPCI 制造商:Advanced Micro Devices 功能描述:
    AM29LV640MU90NI 制造商:Advanced Micro Devices 功能描述:
    AM29LV640MU90RPC1 制造商:Advanced Micro Devices 功能描述:
    AM29LV640MU90RPCI 制造商:Advanced Micro Devices 功能描述:
    AM29LV641DH120REF 制造商:Spansion 功能描述:Flash Memory IC