<code id="ldnwv"><tr id="ldnwv"><output id="ldnwv"></output></tr></code>
  • <button id="ldnwv"><tbody id="ldnwv"></tbody></button>
  • 參數資料
    型號: AM29LV008BT-120EE
    廠商: ADVANCED MICRO DEVICES INC
    元件分類: PROM
    英文描述: 8 Megabit (1 M x 8-Bit) CMOS 3.0 Volt-only Boot Sector Flash Memory
    中文描述: 1M X 8 FLASH 3V PROM, 120 ns, PDSO40
    封裝: MO-142CD, TSOP-40
    文件頁數: 10/38頁
    文件大?。?/td> 492K
    代理商: AM29LV008BT-120EE
    10
    Am29LV008B
    P R E L I M I N A R Y
    Autoselect Mode
    The autoselect mode provides manufacturer and
    device identification, and sector protection verification,
    through identifier codes output on DQ7–DQ0. This
    mode is primarily intended for programming equipment
    to automatically match a device to be programmed with
    its corresponding programming algorithm. However,
    the autoselect codes can also be accessed in-system
    through the command register.
    When using programming equipment, the autoselect
    mode requires V
    ID
    (11.5 V to 12.5 V) on address pin
    A9. Address pins A6, A1, and A0 must be as shown in
    Table 4. In addition, when verifying sector protection,
    the sector address must appear on the appropriate
    highest order address bits (see Tables 2 and 3). Table
    4 shows the remaining address bits that are don’t care.
    When all necessary bits have been set as required, the
    programming equipment may then read the corre-
    sponding identifier code on DQ7–DQ0.
    To access the autoselect codes in-system, the host
    system can issue the autoselect command via the
    command register, as shown in Table 5. This method
    does not require V
    ID
    . See “Command Definitions” for
    details on using the autoselect mode.
    Table 4.
    Am29LV008B Autoselect Codes (High Voltage Method)
    L = Logic Low = V
    IL
    , H = Logic High = V
    IH
    , SA = Sector Address, X = Don’t care.
    Sector Protection/Unprotection
    The hardware sector protection feature disables both
    program and erase operations in any sector. The hard-
    ware sector unprotection feature re-enables both
    program and erase operations in previously protected
    sectors.
    The device is shipped with all sectors unprotected.
    AMD offers the option of programming and protecting
    sectors at its factory prior to shipping the device
    through AMD’s ExpressFlash Service. Contact an
    AMD representative for details.
    It is possible to determine whether a sector is protected
    or unprotected. See “Autoselect Mode” for details.
    Sector protection/unprotection can be implemented via
    two methods.
    The primary method requires V
    ID
    on the RESET# pin
    only, and can be implemented either in-system or via
    programming equipment. Figure 2 shows the algo-
    rithms and Figure 21 shows the waveform. This
    method uses standard microprocessor bus cycle
    timing. For sector unprotect, all unprotected sectors
    must first be protected prior to the first sector unprotect
    write cycle.
    The alternate method intended only for programming
    equipment requires V
    ID
    on address pin A9 and OE#.
    This method is compatible with programmer routines
    written for earlier 3.0 volt-only AMD flash devices.
    Details on this method are provided in a supplement,
    publication number 20875. Contact an AMD represent-
    ative to request a copy.
    Description
    CE#
    OE#
    WE#
    A19
    to
    A13
    A12
    to
    A10
    A9
    A8
    to
    A7
    A6
    A5
    to
    A2
    A1
    A0
    DQ7
    to
    DQ0
    Manufacturer ID
    :
    AMD
    L
    L
    H
    X
    X
    V
    ID
    X
    L
    X
    L
    L
    01h
    Device ID: Am29LV008BT
    (Top Boot Block)
    L
    L
    H
    X
    X
    V
    ID
    X
    L
    X
    L
    H
    3Eh
    Device ID: Am29LV008BB
    (Bottom Boot Block)
    L
    L
    H
    X
    X
    V
    ID
    X
    L
    X
    L
    H
    37h
    Sector Protection Verification
    L
    L
    H
    SA
    X
    V
    ID
    X
    L
    X
    H
    L
    01h
    (protected)
    00h
    (unprotected)
    相關PDF資料
    PDF描述
    Am29LV008BT-120EEB 8 Megabit (1 M x 8-Bit) CMOS 3.0 Volt-only Boot Sector Flash Memory
    AM29LV008BT-120EI 8 Megabit (1 M x 8-Bit) CMOS 3.0 Volt-only Boot Sector Flash Memory
    Am29LV008BT-120EIB 8 Megabit (1 M x 8-Bit) CMOS 3.0 Volt-only Boot Sector Flash Memory
    AM29LV008BT-120FC 8 Megabit (1 M x 8-Bit) CMOS 3.0 Volt-only Boot Sector Flash Memory
    Am29LV008BT-120FCB 8 Megabit (1 M x 8-Bit) CMOS 3.0 Volt-only Boot Sector Flash Memory
    相關代理商/技術參數
    參數描述
    AM29LV008BT-80EC 制造商:Spansion 功能描述:IC 8 MEG X 8, 3 V FLASH TOP B - Bulk
    AM29LV008DT-90EC 制造商:Spansion 功能描述:8M (1MX8) 3V, BOOT BLOCK, TOP, TSOP40, COM - Trays
    AM29LV010B-45JC 制造商:Spansion 功能描述:1M (128KX8) 3V, UNIFORM SECTOR, PLCC32, COM - Rail/Tube
    AM29LV010B-55JCT 制造商:Spansion 功能描述:1M (128KX8) 3V, UNIFORM SECTOR, PLCC32, COM, T&R - Tape and Reel
    AM29LV010B-70ED 制造商:Spansion 功能描述:IC SM FLASH 3V 1MB