- 您現在的位置：買賣IC網 > PDF目錄366448 > AM29LV001BT-45RJCB (ADVANCED MICRO DEVICES INC) 1 Megabit (128 K x 8-Bit) CMOS 3.0 Volt-only Boot Sector Flash Memory PDF資料下載
參數資料
| 型號： | AM29LV001BT-45RJCB |
| 廠商： | ADVANCED MICRO DEVICES INC |
| 元件分類： | PROM |
| 英文描述： | 1 Megabit (128 K x 8-Bit) CMOS 3.0 Volt-only Boot Sector Flash Memory |
| 中文描述： | 128K X 8 FLASH 3V PROM, 45 ns, PQCC32 |
| 封裝： | PLASTIC, LCC-32 |
| 文件頁數： | 10/38頁 |
| 文件大小： | 221K |
| 代理商： | AM29LV001BT-45RJCB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁
Am29LV001B
10
P R E L IM IN A R Y
Autoselect Mode
The autoselect mode provides manufacturer and de-
vice identification, and sector protection verification,
through identifier codes output on DQ7–DQ0. This
mode is primarily intended for programming equipment
to automatically match a device to be programmed with
its corresponding programming algorithm. However,
the autoselect codes can also be accessed in-system
through the command register.
When using programming equipment, the autoselect
mode requires V
ID
(11.5 V to 12.5 V) on address pin
A9. Address pins A6, A1, and A0 must be as shown in
Table 4. In addition, when verifying sector protection,
the sector address must appear on the appropriate
highest order address bits (see Table 2). Table 4 shows
the remaining address bits that are don’t care. When all
necessary bits have been set as required, the program-
ming equipment may then read the corresponding
identifier code on DQ7-DQ0.
To access the autoselect codes in-system, the host
system can issue the autoselect command via the
command register, as shown in Table 5. This method
does not require V
ID
. See “Command Definitions” for
details on using the autoselect mode.
Table 4.
Am29LV001B Autoselect Codes
L = Logic Low = V
IL
, H = Logic High = V
IH
, SA = Sector Address, X = Don’t care.
Sector Protection/Unprotection
The hardware sector protection feature disables both
program and erase operations in any sector. The hard-
ware sector unprotection feature re-enables both pro-
gram and erase operations in previously protected
sectors. Sector protection/unprotection can be imple-
mented via two methods.
The primary method requires V
ID
on the RESET# pin
only, and can be implemented either in-system or via
programming equipment. Figure 1 shows the algo-
rithms and Figure 21 shows the timing diagram. This
method uses standard microprocessor bus cycle tim-
ing. For sector unprotect, all unprotected sectors must
first be protected prior to the first sector unprotect write
cycle.
The alternate method intended only for programming
equipment requires V
ID
on address pin A9, OE#, and
RESET#. This method is compatible with programmer
routines written for earlier 3.0 volt-only AMD flash de-
vices. Publication number 22134 contains further de-
tails; contact an AMD representative to request a copy.
The device is shipped with all sectors unprotected.
AMD offers the option of programming and protecting
sectors at its factory prior to shipping the device
through AMD’s ExpressFlash Service. Contact an
AMD representative for details.
It is possible to determine whether a sector is protected
or unprotected. See “Autoselect Mode” for details.
Temporary Sector Unprotect
This feature allows temporary unprotection of previ-
ously protected sectors to change data in-system. The
Sector Unprotect mode is activated by setting the RE-
SET# pin to V
ID
. During this mode, formerly protected
sectors can be programmed or erased by selecting the
sector addresses. Once V
ID
is removed from the RE-
SET# pin, all the previously protected sectors are
protected again. Figure 2 shows the algorithm, and
Figure 20 shows the timing diagrams, for this feature.
Description
CE#
OE#
WE#
A16
to
A12
A11
to
A10
A9
A8
to
A7
A6
A5
to
A2
A1
A0
DQ7
to
DQ0
Manufacturer ID
:
AMD
L
L
H
X
X
V
ID
X
L
X
L
L
01h
Device ID: Am29LV001BT
(Top Boot Block)
L
L
H
X
X
V
ID
X
L
X
L
H
EDh
Device ID: Am29LV001BB
(Bottom Boot Block)
L
L
H
X
X
V
ID
X
L
X
L
H
6Dh
Sector Protection Verification
L
L
H
SA
X
V
ID
X
L
X
H
L
01h
(protected)
00h
(unprotected)
相關PDF資料 |
PDF描述 |
|---|---|
| Am29LV001BT-45RJE | 1 Megabit (128 K x 8-Bit) CMOS 3.0 Volt-only Boot Sector Flash Memory |
| AM29LV001BT-45RJI | 1 Megabit (128 K x 8-Bit) CMOS 3.0 Volt-only Boot Sector Flash Memory |
| AM29LV001BT-55ECB | 1 Megabit (128 K x 8-Bit) CMOS 3.0 Volt-only Boot Sector Flash Memory |
| AM29LV001BT-55EE | 1 Megabit (128 K x 8-Bit) CMOS 3.0 Volt-only Boot Sector Flash Memory |
| AM29LV001BT-55EEB | 1 Megabit (128 K x 8-Bit) CMOS 3.0 Volt-only Boot Sector Flash Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AM29LV001BT-55ED | 制造商:Spansion 功能描述:1M (128KX8) 3V, BOOT BLOCK, TOP, TSOP32, COM - Trays |
| AM29LV002BB-90EC | 制造商:Advanced Micro Devices 功能描述: |
| AM29LV002BT-90EF | 制造商:Spansion 功能描述:NOR Flash Parallel 3V/3.3V 2Mbit 256K x 8bit 90ns 40-Pin TSOP |
| AM29LV002BT-90EI\\T | 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 2MBIT 256KX8 90NS 40TSOP - Tape and Reel |
| AM29LV002BT-90EI\T | 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 2MBIT 256KX8 90NS 40TSOP - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。