參數資料
型號： AM29F002
廠商： Advanced Micro Devices, Inc.
英文描述： High Speed CMOS Logic Inverting Octal Buffer/Line Drivers with 3-State Outputs 20-CDIP -55 to 125
中文描述： 2兆位（256畝× 8位）的CMOS 5.0伏，只引導扇區閃存
文件頁數： 9/40頁
文件大?。?/td> 792K
代理商： AM29F002
8
Am29F002B/Am29F002NB
November 28, 2000
DEVICE BUS OPERATIONS
This section describes the requirements and use of the
device bus operations, which are initiated through the
internal command register. The command register itself
does not occupy any addressable memory location.
The register is composed of latches that store the com-
mands, along with the address and data information
needed to execute the command. The contents of the
register serve as inputs to the internal state machine.
The state machine outputs dictate the function of the
device. The appropriate device bus operations table
lists the inputs and control levels required, and the
resulting output. The following subsections describe
each of these operations in further detail.
Table 1.
Am29F002B/Am29F002NB Device Bus Operations
Legend:
L = Logic Low = VIL, H = Logic High = VIH, VID = 12.0 ± 0.5 V, X = Don’t Care, DIN = Data In, DOUT = Data Out, A
IN
= Address In
Note:
See the sections on Sector Group Protection and Temporary Sector Unprotect for more information. This function requires
the RESET# pin and is therefore not available on the Am29F002NB device.
Requirements for Reading Array Data
To read array data from the outputs, the system must
drive the CE# and OE# pins to V
IL
. CE# is the power
control and selects the device. OE# is the output
control and gates array data to the output pins. WE#
should remain at V
IH
.
The internal state machine is set for reading array data
upon device power-up, or after a hardware reset. This
ensures that no spurious alteration of the memory
content occurs during the power transition. No
command is necessary in this mode to obtain array
data. Standard microprocessor read cycles that assert
valid addresses on the device address inputs produce
valid data on the device data outputs. The device
remains enabled for read access until the command
register contents are altered.
See “Reading Array Data” for more information. Refer
to the AC Read Operations table for timing specifica-
tions and to the Read Operations Timings diagram for
the timing waveforms. I
CC1
in the DC Characteristics
table represents the active current specification for
reading array data.
Writing Commands/Command Sequences
To write a command or command sequence (which
includes programming data to the device and erasing
sectors of memory), the system must drive WE# and
CE# to V
IL
, and OE# to V
IH
.
An erase operation can erase one sector, multiple sec-
tors, or the entire device. The Sector Address Tables
indicate the address space that each sector occupies.
A “sector address” consists of the address bits required
to uniquely select a sector. See the Command Defini-
tions section for details on erasing a sector or the entire
chip, or suspending/resuming the erase operation.
After the system writes the autoselect command
sequence, the device enters the autoselect mode. The
system can then read autoselect codes from the
internal register (which is separate from the memory
array) on DQ7–DQ0. Standard read cycle timings
apply in this mode. Refer to the “Autoselect Mode” and
Autoselect Command Sequence sections for more
information.
I
CC2
in the DC Characteristics table represents the
active current specification for the write mode. The “AC
Characteristics” section contains timing specification
tables and timing diagrams for write operations.
Program and Erase Operation Status
During an erase or program operation, the system may
check the status of the operation by reading the status
bits on DQ7–DQ0. Standard read cycle timings and I
CC
read specifications apply. Refer to “Write Operation
Operation
CE#
L
L
OE#
L
H
X
X
H
X
WE#
H
L
X
X
H
X
RESET#
(n/a Am29F002NB)
H
H
H
H
H
L
A0–A17
A
IN
A
IN
X
X
X
X
DQ0–DQ7
D
OUT
D
IN
High-Z
High-Z
High-Z
High-Z
Read
Write
CMOS Standby
TTL Standby
Output Disable
Reset (n/a on Am29F002NB)
Temporary Sector Unprotect
(See Note)
V
CC
± 0.5 V
H
L
X
X
X
X
V
ID
X
X
相關PDF資料
PDF描述
AM29F002B High Speed CMOS Logic Non-Inverting Octal Buffer/Line Drivers with 3-State Outputs 20-CDIP -55 to 125
AM29F002B-120JC 2 Megabit (256 K x 8-Bit) CMOS 5.0 Volt-only Boot Sector Flash Memory
Am29F002B-120JCB 2 Megabit (256 K x 8-Bit) CMOS 5.0 Volt-only Boot Sector Flash Memory
AM29F002B-120JE High Speed CMOS Logic Non-Inverting Octal Buffer/Line Drivers with 3-State Outputs 20-CDIP -55 to 125
Am29F002B-120JEB 2 Megabit (256 K x 8-Bit) CMOS 5.0 Volt-only Boot Sector Flash Memory
相關代理商/技術參數
參數描述
AM29F002B-70JC 制造商:Advanced Micro Devices 功能描述:NOR Flash, 256K x 8, 32 Pin, Plastic, PLCC
AM29F002BB-120EC 制造商:Spansion 功能描述:2M (256KX8) 5V, BOOT BLOCK, BOT, TSOP32, COM - Trays
AM29F002BB-120JCT 制造商:Spansion 功能描述:2M (256KX8) 5V, BOOT BLOCK, BOT, PLCC32, COM, T&R - Tape and Reel
AM29F002BB-55EC 制造商:Spansion 功能描述:
AM29F002BB-55JF 制造商:Spansion 功能描述:NOR Flash Parallel 5V 2Mbit 256K x 8bit 55ns 32-Pin PLCC
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*