- 您現在的位置：買賣IC網 > PDF目錄366410 > AM29DS323DB50WMIN (Advanced Micro Devices, Inc.) 32 Megabit (4 M x 8-Bit/2 M x 16-Bit) CMOS 1.8 Volt-only, Simultaneous Operation Flash Memory PDF資料下載
參數資料
| 型號： | AM29DS323DB50WMIN |
| 廠商： | Advanced Micro Devices, Inc. |
| 英文描述： | 32 Megabit (4 M x 8-Bit/2 M x 16-Bit) CMOS 1.8 Volt-only, Simultaneous Operation Flash Memory |
| 中文描述： | 32兆位（4個M × 8位/ 2米x 16位），1.8伏的CMOS只，同時作業快閃記憶體 |
| 文件頁數： | 30/56頁 |
| 文件大?。?/td> | 641K |
| 代理商： | AM29DS323DB50WMIN |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁當前第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁
28
Am29DS323D
23480A5 October10,2006
D A T A S H E E T
Command Definitions
Table 14.
Am29DS323D Command Definitions
Legend:
X = Don’t care
RA = Address of the memory location to be read.
RD = Data read from location RA during read operation.
PA = Address of the memory location to be programmed. Addresses
latch on the falling edge of the WE# or CE# pulse, whichever happens
later.
PD = Data to be programmed at location PA. Data latches on the rising
edge of WE# or CE# pulse, whichever happens first.
SA = Address of the sector to be verified (in autoselect mode) or
erased. Address bits A20–A12 uniquely select any sector.
BA = Address of the bank that is being switched to autoselect mode, is
in bypass mode, or is being erased.
Notes:
1.
2.
3.
See
Table 1
for description of bus operations.
All values are in hexadecimal.
Except for the read cycle and the fourth cycle of the autoselect
command sequence, all bus cycles are write cycles.
Data bits DQ15–DQ8 are don’t care in command sequences,
except for RD and PD.
Unless otherwise noted, address bits A20–A11 are don’t cares.
No unlock or command cycles required when bank is in read
mode.
The Reset command is required to return to reading array data
(or to the erase-suspend-read mode if previously in Erase
Suspend) when a bank is in the autoselect mode, or if DQ5 goes
high (while the bank is providing status information).
The fourth cycle of the autoselect command sequence is a read
cycle. The system must provide the bank address to obtain the
manufacturer ID, device ID, or Secured Silicon Sector factory
protect information. Data bits DQ15–DQ8 are don’t care. See the
Autoselect Command Sequence section for more information.
4.
5.
6.
7.
8.
9.
10. The data is 00h for an unprotected sector/sector block and 01h for
a protected sector/sector block.
11. The Unlock Bypass command is required prior to the Unlock
Bypass Program command.
12. The Unlock Bypass Reset command is required to return to
reading array data when the bank is in the unlock bypass mode.
13. The system may read and program in non-erasing sectors, or
enter the autoselect mode, when in the Erase Suspend mode.
The Erase Suspend command is valid only during a sector erase
operation, and requires the bank address.
14. The Erase Resume command is valid only during the Erase
Suspend mode, and requires the bank address.
The data is 85h for factory locked and 05h for not factory locked.
15. Command is valid when device is ready to read array data or when
device is in autoselect mode.
Command
Sequence
(Note 1)
C
Bus Cycles (Notes 2–5)
Third
Addr
Data
First
Second
Addr
Fourth
Fifth
Sixth
Addr Data
RA
XXX
555
AAA
555
AAA
555
AAA
555
AAA
555
AAA
555
AAA
555
AAA
555
AAA
XXX
BA
555
AAA
555
AAA
BA
BA
55
AA
Data
Addr
Data
Addr
Data
Addr
Data
Read
(Note 6)
Reset
(Note 7)
1
1
RD
F0
A
(
Manufacturer ID
Word
Byte
Word
Byte
Word
Byte
Word
Byte
Word
Byte
Word
Byte
Word
Byte
Word
Byte
4
AA
2AA
555
2AA
555
2AA
555
2AA
555
2AA
555
2AA
555
2AA
555
2AA
555
PA
XXX
2AA
555
2AA
555
55
(BA)555
(BA)AAA
(BA)555
(BA)AAA
(BA)555
(BA)AAA
(BA)555
(BA)AAA
555
AAA
555
AAA
555
AAA
555
AAA
90
(BA)X00
01
Device ID
4
AA
55
90
(BA)X01
(BA)X02
(BA)X03
(BA)X06
(SA)X02
(SA)X04
(
Table 7
)
Secured Silicon Sector
Factory Protect
(Note 9)
4
AA
55
90
85/05
Sector Protect Verify
(Note
10)
4
AA
55
90
00/01
Enter Secured Silicon Sector
Region
3
AA
55
88
Exit Secured Silicon Sector
Region
4
AA
55
90
XXX
00
Program
4
AA
55
A0
PA
PD
Unlock Bypass
3
AA
55
20
Unlock Bypass Program
(Note 11)
Unlock Bypass Reset
(Note 12)
2
2
A0
90
PD
00
Chip Erase
Word
Byte
Word
Byte
6
AA
55
555
AAA
555
AAA
80
555
AAA
555
AAA
AA
2AA
555
2AA
555
55
555
AAA
10
Sector Erase
6
AA
55
80
AA
55
SA
30
Erase Suspend
(Note 13)
Erase Resume
(Note 14)
1
1
B0
30
CFI Query
(Note 15)
Word
Byte
1
98
相關PDF資料 |
PDF描述 |
|---|---|
| AM29DS323DT50EI | 32 Megabit (4 M x 8-Bit/2 M x 16-Bit) CMOS 1.8 Volt-only, Simultaneous Operation Flash Memory |
| AM29DS323DT50EIN | 32 Megabit (4 M x 8-Bit/2 M x 16-Bit) CMOS 1.8 Volt-only, Simultaneous Operation Flash Memory |
| AM29DS323DT50WMI | 32 Megabit (4 M x 8-Bit/2 M x 16-Bit) CMOS 1.8 Volt-only, Simultaneous Operation Flash Memory |
| AM29DS323DT50WMIN | 32 Megabit (4 M x 8-Bit/2 M x 16-Bit) CMOS 1.8 Volt-only, Simultaneous Operation Flash Memory |
| AM29DS323DT110EIN | 32 Megabit (4 M x 8-Bit/2 M x 16-Bit) CMOS 1.8 Volt-only, Simultaneous Operation Flash Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AM29DS323DT-110WMI | 制造商:Spansion 功能描述:NOR Flash Parallel 32Mbit 4M/2M x 8bit/16bit 110ns 48-Pin FBGA |
| AM29DS323DT11WMINS | 制造商:Advanced Micro Devices 功能描述: |
| AM29F002B-70JC | 制造商:Advanced Micro Devices 功能描述:NOR Flash, 256K x 8, 32 Pin, Plastic, PLCC |
| AM29F002BB-120EC | 制造商:Spansion 功能描述:2M (256KX8) 5V, BOOT BLOCK, BOT, TSOP32, COM - Trays |
| AM29F002BB-120JCT | 制造商:Spansion 功能描述:2M (256KX8) 5V, BOOT BLOCK, BOT, PLCC32, COM, T&R - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。