參數資料
型號： AM29BDS320GBC3VMI
廠商： SPANSION LLC
元件分類： DRAM
英文描述： 32 Megabit (2 M x 16-Bit), 1.8 Volt-only Simultaneous Read/Write, Burst Mode Flash Memory
中文描述： 2M X 16 FLASH 1.8V PROM, 90 ns, PBGA64
封裝： 8 X 9 MM, 0.80 MM PITCH, FBGA-64
文件頁數： 27/74頁
文件大?。?/td> 701K
代理商： AM29BDS320GBC3VMI
October 1, 2003 27243B1
Am29BDS320G
25
P r e l i m i n a r y
Command Definitions
Writing specific address and data commands or sequences into the command
register initiates device operations.
Table 14, “Command Definitions,” on page 36
defines the valid register command sequences. Note that writing incorrect ad-
dress and data values or writing them in the improper sequence may place the
device in an unknown state. A reset command is required to return the device to
normal operation.
Refer to the AC Characteristics section for timing diagrams.
Reading Array Data
The device is automatically set to reading array data after device power-up. No
commands are required to retrieve data in asynchronous mode. Each bank is
ready to read array data after completing an Embedded Program or Embedded
Erase algorithm.
After the device accepts an Erase Suspend command, the corresponding bank
enters the erase-suspend-read mode, after which the system can read data from
any non-erase-suspended sector within the same bank. After completing a pro-
gramming operation in the Erase Suspend mode, the system may once again
read array data with the same exception. See the
“Erase Suspend/Erase Resume
Commands” section on page 34
section for more information.
The system must issue the reset command to return a bank to the read (or erase-
suspend-read) mode if DQ5 goes high during an active program or erase opera-
tion, or if the bank is in the autoselect mode. See the
“Reset Command” section
on page 30
section for more information.
See also
“Requirements for Asynchronous Read Operation (Non-Burst)”
and
“Re-
quirements for S ynchronous ( Burst) Read Operation”
sections for more
information. The Asynchronous Read and Synchronous/Burst Read tables provide
the read parameters, and Figures
11
,
13
, and
18
show the timings.
Set Burst Mode Configuration Register Command Sequence
The device uses a burst mode configuration register to set the various burst pa-
rameters: number of wait states, burst read mode, active clock edge, RDY
configuration, and synchronous mode active. The burst mode configuration reg-
ister must be set before the device will enter burst mode.
The burst mode configuration register is loaded with a three-cycle command se-
quence. The first two cycles are standard unlock sequences. On the third cycle,
the data should be C0h, address bits A11–A0 should be 555h, and address bits
A19–A12 set the code to be latched. The device will power up or after a hardware
reset with the default setting, which is in asynchronous mode. The register must
be set before the device can enter synchronous mode. The burst mode configu-
ration register can not be changed during device operations (program, erase, or
sector lock).
相關PDF資料
PDF描述
AM29BDS320GBC4VMI 32 Megabit (2 M x 16-Bit), 1.8 Volt-only Simultaneous Read/Write, Burst Mode Flash Memory
AM29BDS320GBC8VMI 32 Megabit (2 M x 16-Bit), 1.8 Volt-only Simultaneous Read/Write, Burst Mode Flash Memory
AM29BDS320GBC9VMI 32 Megabit (2 M x 16-Bit), 1.8 Volt-only Simultaneous Read/Write, Burst Mode Flash Memory
AM29BDS320GBD3VMI 32 Megabit (2 M x 16-Bit), 1.8 Volt-only Simultaneous Read/Write, Burst Mode Flash Memory
AM29BDS320GBD4VMI 32 Megabit (2 M x 16-Bit), 1.8 Volt-only Simultaneous Read/Write, Burst Mode Flash Memory
相關代理商/技術參數
參數描述
AM29BDS643GT5KVAI 制造商:Spansion 功能描述:FLASH PARALLEL 1.8V 64MBIT 4MX16 55NS 44FBGA - Trays
AM29BL802CB-65RZET 制造商:Spansion 功能描述:
AM29C01WW WAF 制造商:Advanced Micro Devices 功能描述:
AM29C10API 制造商:Rochester Electronics LLC 功能描述:- Bulk
AM29C10AWW DIE 制造商:Advanced Micro Devices 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*