- 您現在的位置：買賣IC網 > PDF目錄366390 > AM28F256-70PEB (Advanced Micro Devices, Inc.) Octal bus transceivers 20-SOIC 0 to 70 PDF資料下載
參數資料
| 型號： | AM28F256-70PEB |
| 廠商： | Advanced Micro Devices, Inc. |
| 英文描述： | Octal bus transceivers 20-SOIC 0 to 70 |
| 中文描述： | 256千比特（32畝× 8位）的CMOS 12.0伏，整體擦除閃存 |
| 文件頁數： | 13/35頁 |
| 文件大小： | 493K |
| 代理商： | AM28F256-70PEB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁
Am28F256
13
FLASHERASE
ELECTRICAL ERASE ALGORITHM
This Flash memory device erases the entire array in
parallel. The erase time depends on V
PP
, temperature,
and number of erase/program cycles on the device. In
general, reprogramming time increases as the number
of erase/program cycles increases.
The Flasherase electrical erase algorithm employs an
interactive closed loop flow to simultaneously erase all
bits in the array. Erasure begins with a read of the mem-
ory contents. The device is erased when shipped from
the factory. Reading FFh data from the device would
immediately be followed by executing the Flashrite pro-
gramming algorithm with the appropriate data pattern.
Should the device be currently programmed, data other
than FFh will be returned from address locations.
Follow the Flasherase algorithm. Uniform and reliable
erasure is ensured by first programming all bits in the
device to their charged state (Data = 00h). This is
accomplished using the Flashrite Programming
algorithm. Erasure then continues with an initial erase
operation. Erase verification (Data = FFh) begins at
address 0000h and continues through the array to the
last address, or until data other than FFh is
encountered. If a byte fails to verify, the device is
erased again. With each erase operation, an
increasing number of bytes verify to the erased state.
Typically, devices are erased in less than 100 pulses
(one second). Erase efficiency may be improved by
storing the address of the last byte that fails to verify in
a register. Following the next erase operation,
verification may start at the stored address location. A
total of 1000 erase pulses are allowed per reprogram
cycle, which corresponds to approximately 10 seconds
of cumulative erase time. The entire sequence of erase
and byte verification is performed with high voltage
applied to the V
PP
pin. Figure 1 illustrates the electrical
erase algorithm.
Table 4.
Flasherase
Electrical Erase Algorithm
Notes:
1. See AC and DC Characteristics for values of V
PP
parameters. The V
PP
power supply can be hard-wired to the device or
switchable. When V
PP
is switched, V
PPL
may be ground, no connect with a resistor tied to ground, or less than V
CC
+ 2.0 V
2. Erase Verify is performed only after chip erasure. A final read compare may be performed (optional) after the register is written
with the read command.
3. The erase algorithm
Must Be Followed
to ensure proper and reliable operation of the device.
Bus Operations
Command
Comments
Entire memory must = 00h before erasure (Note 3)
Note:
Use Flashrite
programming algorithm (Figure 3) for
programming.
Standby
Wait for V
PP
Ramp to V
PPH
(Note 1)
Initialize:
Addresses
PLSCNT (Pulse count)
Write
Erase Setup
Data = 20h
Erase
Data = 20h
Standby
Duration of Erase Operation (t
WHWH2
)
Write
Erase-Verify (Note 2)
Address = Byte to Verify
Data = A0h
Stops Erase Operation
Standby
Write Recovery Time before Read = 6 μs
Read
Read byte to verify erasure
Standby
Compare output to FFh
Increment pulse count
Write
Reset
Data = FFh, reset the register for read operations
Standby
Wait for V
PP
Ramp to V
PPL
(Note 1)
相關PDF資料 |
PDF描述 |
|---|---|
| AM28F256-70PI | 256 Kilobit (32 K x 8-Bit) CMOS 12.0 Volt, Bulk Erase Flash Memory |
| AM28F256-70PIB | 256 Kilobit (32 K x 8-Bit) CMOS 12.0 Volt, Bulk Erase Flash Memory |
| AM28F256-90EC | 256 Kilobit (32 K x 8-Bit) CMOS 12.0 Volt, Bulk Erase Flash Memory |
| AM28F256-90ECB | 256 Kilobit (32 K x 8-Bit) CMOS 12.0 Volt, Bulk Erase Flash Memory |
| AM28F256-90EE | 256 Kilobit (32 K x 8-Bit) CMOS 12.0 Volt, Bulk Erase Flash Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AM28F256-70PI | 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:256 Kilobit (32 K x 8-Bit) CMOS 12.0 Volt, Bulk Erase Flash Memory |
| AM28F256-70PIB | 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:256 Kilobit (32 K x 8-Bit) CMOS 12.0 Volt, Bulk Erase Flash Memory |
| AM28F256-75LC | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x8 Flash EEPROM |
| AM28F256-90C3JC | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x8 Flash EEPROM |
| AM28F256-90C3PC | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x8 Flash EEPROM |
發布緊急采購，3分鐘左右您將得到回復。