• <big id="vtbsz"><strike id="vtbsz"><dl id="vtbsz"></dl></strike></big>
    <dl id="vtbsz"><legend id="vtbsz"></legend></dl>
    <small id="vtbsz"><noframes id="vtbsz">
    <small id="vtbsz"><ul id="vtbsz"><ins id="vtbsz"></ins></ul></small>
  • <thead id="vtbsz"><sup id="vtbsz"><ins id="vtbsz"></ins></sup></thead>
  • <big id="vtbsz"></big><center id="vtbsz"></center>
      <big id="vtbsz"><xmp id="vtbsz">
      參數資料
      型號: AM27C040-90PC
      廠商: ADVANCED MICRO DEVICES INC
      元件分類: PROM
      英文描述: 4 Megabit (512 K x 8-Bit) CMOS EPROM
      中文描述: 512K X 8 OTPROM, 90 ns, PDIP32
      封裝: PLASTIC, DIP-32
      文件頁數: 6/13頁
      文件大?。?/td> 175K
      代理商: AM27C040-90PC
      6
      Am27C040
      F I N A L
      common connection to all devices in the array and con-
      nected to the READ line from the system control bus.
      This assures that all deselected memory devices are in
      their low-power standby mode and that the output pins
      are only active when data is desired from a particular
      memory device.
      System Applications
      During the switch between active and standby condi-
      tions, transient current peaks are produced on the ris-
      ing and falling edges of Chip Enable. The magnitude of
      these transient current peaks is dependent on the out-
      put capacitance loading of the device. At a minimum, a
      0.1
      μF ceramic capacitor (high frequency, low inherent
      inductance) should be used on each device between
      V
      CC
      and V
      SS
      to minimize transient effects. In addition,
      to overcome the voltage drop caused by the inductive
      effects of the printed circuit board traces on EPROM ar-
      rays, a 4.7 μF bulk electrolytic capacitor should be used
      between V
      CC
      and V
      SS
      for each eight devices. The loca-
      tion of the capacitor should be close to where the
      power supply is connected to the array.
      MODE SELECT TABLE
      Note:
      1. V
      H
      = 12.0 V
      ±
      0.5 V.
      2. X = Either V
      IH
      or V
      IL
      3.
      A1 – A8 = A10 – A18 = V
      IL
      4. See DC Programming Characteristics in the EPROM Products Data Book for V
      PP
      voltage during programming
      Mode
      CE#/PGM#
      OE#
      A0
      A9
      V
      PP
      Outputs
      Read
      V
      IL
      V
      IL
      X
      X
      X
      D
      OUT
      Output Disable
      V
      IL
      V
      IH
      X
      X
      X
      HIGH Z
      Standby (TTL)
      V
      IH
      X
      X
      X
      X
      HIGH Z
      Standby (CMOS)
      V
      CC
      + 0.3 V
      X
      X
      X
      X
      HIGH Z
      Program
      V
      IL
      V
      IH
      X
      X
      V
      PP
      D
      IN
      Program Verify
      V
      IL
      V
      IL
      X
      X
      V
      PP
      D
      OUT
      Program Inhibit
      V
      IH
      X
      X
      X
      V
      PP
      HIGH Z
      Auto Select
      (Note 3)
      Manufacturer Code
      V
      IL
      V
      IL
      V
      IL
      V
      H
      X
      01h
      Device Code
      V
      IL
      V
      IL
      V
      IH
      V
      H
      X
      9Bh
      相關PDF資料
      PDF描述
      AM27C040-90PE SEAL,NEOPRENE,CYLINDRICAL CONNECTR&
      AM27C040-120DEB 4 Megabit (512 K x 8-Bit) CMOS EPROM
      AM27C040-120DIB 4 Megabit (512 K x 8-Bit) CMOS EPROM
      AM27C040-150DCB 4 Megabit (512 K x 8-Bit) CMOS EPROM
      AM27C040-150DEB 4 Megabit (512 K x 8-Bit) CMOS EPROM
      相關代理商/技術參數
      參數描述
      AM27C040-90PE 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:4 Megabit (512 K x 8-Bit) CMOS EPROM
      AM27C040-90PI 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:4 Megabit (512 K x 8-Bit) CMOS EPROM
      AM27C040-95DC 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x8 EPROM
      AM27C040-95DCB 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x8 EPROM
      AM27C040-95DI 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x8 EPROM