- 您現在的位置：買賣IC網 > PDF目錄385098 > AKD4527B.(AKD4527B) (Asahi Kasei Microsystems Co.,Ltd) Evaluation board Rev.D for AK4527B PDF資料下載
參數資料
| 型號： | AKD4527B.(AKD4527B) |
| 廠商： | Asahi Kasei Microsystems Co.,Ltd |
| 英文描述： | Evaluation board Rev.D for AK4527B |
| 中文描述： | 評估板Rev.D的AK4527B |
| 文件頁數： | 5/40頁 |
| 文件大?。?/td> | 348K |
| 代理商： | AKD4527B.(AKD4527B) |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
ASAHI KASEI
[AKD4527B Rev.D]
<KM063700>
- 5 -
’00/9
PORT3
uP-I/F
1
2
9
CSN
10
CCLK
CDTI
CDTO
n
Operation sequence
(1)
Set up the power supply lines.
[+12V] (orange jack) = +12
～
+15V
[-12V] (blue jack) = -12
～
-15V
[AGND] (black jack) = 0V
[DGND] (black jack) = 0V
Each supply line should be distributed from the power supply unit.
±
12V are supplied to analog interface.
+12V is regulated to +5V and +3.3V by regulators(T1,T2).
+5V is supplied to digital interface, AK4527B and TVDD of AK4112A.
+3.3V is supplied to AVDD and DVDD of AK4112A.
(2)
Set up the evaluation mode and jumper pins.
(See p.3.)
(3)
Connect Optical or BNC connector.
[PORT2] (OPT_IN) : Optical input to RX1 of AK4112A
[J10] (RX2) : BNC input to RX1 of AK4112A
(4)
Power on.
The AK4527B, AK4112A and AK4353 should be reset once bringing PDN(SW1) “L” upon power-up.
(5)
Adjust the interface format
Serial control is needed after the reset by SW1. The default value for interface format of
AK4527B, AK4112A, and AK4353 is “Right justified, 20 bit”, “Left justified, 24 bit”, and “I
2
S”, respectively.
The software “4527.exe” packed with the AKD4527B is used for the set-up of the AK4527B.
Evaluation mode 1 : DIF1-0 bit of the AK4527B should be set to “11” .
Evaluation mode 2, 3: DIF1-0 bit of the AK4527B should be set to “10”.
Evaluation mode 4 : AK4112A and AK4527B should be set to adjust the format of DSP.
(6)
Set up software.
The control mode of AK4527B and AK4112A is fixed to “serial”.
The AKD4527B can be controlled via the printer port (parallel port) of IBM-AT
compatible PC. Connect PORT3(uP-I/F) with PC by 10-line flat cable
packed with the AKD4527B.
Take care of the direction of connector. There is a mark at pin#1.
The pin layout of PORT3 is as Figure 2. Figure 2. PORT3 pin layout
相關PDF資料 |
PDF描述 |
|---|---|
| AKD4528 | EVALUATION BOARD FOR AK4528 REV.C |
| AKD4550 | EVALUATION BOARD REV.C FOR AK4550 |
| AKD4550(AKD4550) | Evaluation board Rev.C for AK4550 |
| AKD4550.(AKD4550) | Evaluation board Rev.C for AK4550 |
| AKD4551 | EVALUATION BOARD REV.C FOR AK4551 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AKD4528 | 制造商:AKM 制造商全稱:AKM 功能描述:High Performance 24Bit 96kHz Audio CODEC |
| AKD4528_05 | 制造商:AKM 制造商全稱:AKM 功能描述:24Bit A/D & D/A converter |
| AKD4529 | 制造商:AKM 制造商全稱:AKM 功能描述:High Performance Multi-channel Audio CODEC |
| AKD4532 | 制造商:AKM 制造商全稱:AKM 功能描述:Internet/Network/General Purpose Multimedia Audio CODEC |
| AKD4534 | 制造商:AKM 制造商全稱:AKM 功能描述:16Bit CODEC with MIC/HP/SPK-AMP |
發布緊急采購，3分鐘左右您將得到回復。