參數資料
型號： AK4586
廠商： Asahi Kasei Microsystems Co.,Ltd
元件分類： Codec
英文描述： MULTI CHANNEL AUDIO CODEC WITH DIR
中文描述： 多通道音頻編解碼器迪爾
文件頁數： 17/54頁
文件大?。?/td> 586K
代理商： AK4586
ASAHI KASEI
[AK4586]
MS0097-E-01
2001/12
- 17 -
OPERATION OVERVIEW
Non-PCM (AC-3, MPEG, etc.), DTS-CD Bitstream Detect
The AK4586 has the Non-PCM steam auto detect function. When the 32bit mode Non-PCM preamble based on Dolby
“AC-3 Data Stream in IEC60958 Interface” is detected, the AUTO bit goes to “1”. The 16bit mode Non-PCM preamble is
not detected. The AUTO bit remains “0” at that time. The 96bit sync code consists of 0x0000, 0x0000, 0x0000, 0x0000,
0xF872 and 0x4E1F. Detection of this pattern will set the AUTO bit “1”. Once the AUTO is set to “1”, it will remain “1”
until 4096 frames pass through the chip without additional sync pattern being detected. When those preambles are
detected, the burst preambles Pc and Pd that follow those sync codes are stored to registers 0DH-10H. The AK4586 also
has the DTS-CD stream auto detect function. When the AK4586 detects the DTS-CD bitstreams, the DTSCD bit goes to
“1”. When the next sync code does not come within 4096 flames, the DTSCD bit goes to “0” until the AK4586 detects the
stream again.
Clock Recovery and 96kHz Detect
On chip low jitter PLL has a wide lock range with 32kHz to 96kHz and the lock time is less than 20ms. The 96kHz detect
bit RFS96 goes to “1” when the sampling rate is 88.2kHz or more and “0” at 48kHz or less. PLL loses lock when the
received sync interval is incorrect.
Clock Operation Mode
The CM0 and CM1 bits select the clock source of MCKO and the data source of SDTO (Table 1). In mode 2, the clock
source is switched from PLL to X'tal when PLL goes to the unlock state. In mode 3, the clock source is fixed to X'tal, but
PLL is also operating and the recovered data such as C bits can be monitored.
Mode
CM1
CM0
UNLOCK
PLL
0
0
0
-
ON
1
0
1
-
OFF
0
ON
2
1
0
1
ON
3
1
1
-
ON
ON: Oscillation (Power-up), OFF: STOP (Power-down)
Table 1. Clock Operation Mode Select
System Clock
The AK4586 has the master clock output pin, MCKO. This clock is derived from either the recovered clock or from the
crystal oscillator. In the PLL mode, the frequency of the master clock output (MCKO) is set by OCKS0 and OCKS1 bits
as shown in Table 2. 96kHz sampling is not supported at mode 2. MCKO goes to “L” when the AK4586 detect 96kHz
sampling at mode 2. Sampling speed mode is set by RFS96 or XFS96 bit (Table 3). In the x’tal mode, the x’tal frequency
rate to fs is set by ICKS1-0 bits (Table 4). In the x’tal mode, the frequency of the MCKO pin becomes half of the crystal
oscillator if the CLKDIV bit is set to “1” (Table 5). ICKS1-0 and XFS96 bits should be changed while RSTN bit is “0”. If
the external clocks are not present, the AK4586 should be in the power-down mode (PDN= “L”) or in the reset mode
(RSTN= “0”).
Mode
OCKS1
OCKS0
MCKO
0
0
0
256fs
1
0
1
128fs
2
1
0
512fs
3
1
1
Table 2. Master Clock Output Frequency Select (PLL mode)
X'tal
OFF
ON
ON
ON
ON
Clock source
PLL
X'tal
PLL
X'tal
X'tal
SDTO
RX
ADC
RX
ADC
ADC
Default
fs
32kHz~96kHz
32kHz~96kHz
32kHz~48kHz
Reserved
Default
相關PDF資料
PDF描述
AK4586VQ Circular Connector; MIL SPEC:MIL-C-5015 A/B/C; Body Material:Aluminum Alloy; Series:97-3100A; No. of Contacts:4; Connector Shell Size:18; Connecting Termination:Solder; Circular Shell Style:Wall Mount Receptacle RoHS Compliant: No
AK4588 2/8 CHANNEL AUDIO CODEC WITH DIR
AK4588VQ 2/8 CHANNEL AUDIO CODEC WITH DIR
AK4589VQ 2/8-Channel Audio CODEC with DIR
AK4591 24bit 4ch ADC + 24bit 6ch DAC
相關代理商/技術參數
參數描述
AK4586VQ 制造商:AKM 制造商全稱:AKM 功能描述:MULTI CHANNEL AUDIO CODEC WITH DIR
AK4588 制造商:AKM 制造商全稱:AKM 功能描述:2/8 CHANNEL AUDIO CODEC WITH DIR
AK4588VQ 制造商:AKM 制造商全稱:AKM 功能描述:2/8 CHANNEL AUDIO CODEC WITH DIR
AK4589 制造商:AKM 制造商全稱:AKM 功能描述:2/8 CHANNEL AUDIO CODEC WITH DIR
AK4589_1 制造商:AKM 制造商全稱:AKM 功能描述:2/8-Channel Audio CODEC with DIR
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*