- 您現在的位置：買賣IC網 > PDF目錄385090 > AK4220VQ (ASAHI KASEI POWER DEVICES CORP) 7:3 Audio Switch and 6:3 Video Switch PDF資料下載
參數資料
| 型號： | AK4220VQ |
| 廠商： | ASAHI KASEI POWER DEVICES CORP |
| 元件分類： | 消費家電 |
| 英文描述： | 7:3 Audio Switch and 6:3 Video Switch |
| 中文描述： | SPECIALTY CONSUMER CIRCUIT, PQFP64 |
| 封裝： | 0.50 MM PITCH, LEAD FREE, PLASTIC, LQFP-64 |
| 文件頁數： | 30/33頁 |
| 文件大?。?/td> | 537K |
| 代理商： | AK4220VQ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁當前第30頁第31頁第32頁第33頁
I
[AK4220]
MS0627-E-00
2007/05
- 30 -
1. Grounding and Power Supply Decoupling
The AK4220 requires careful attention to power supply and grounding arrangements. AVDD, VVDD1-2 and DVDD are
usually supplied from the analog power supply in the system. Alternatively if AVDD, VVDD1-2 and DVDD are supplied
separately, the power up sequence is not critical. AVSS, VVSS1-3 and DVSS must be connected to the analog ground
plane. System analog ground and digital ground should be connected together near to where the supplies are brought onto
the printed circuit board. Decoupling capacitors should be as close to the AK4220 as possible, with the small value
ceramic capacitors being the nearest.
2. Voltage Reference
VCOM is a signal ground of this chip. A 2.2
μ
F electrolytic capacitor in parallel with a 0.1
μ
F ceramic capacitor attached
between VCOM and AVSS eliminates the effects of high frequency noise. No load current may be drawn from VCOM
pin. All signals, especially clocks, should be kept away from VCOM in order to avoid unwanted coupling into the
AK4220. MUTET is an audio output common voltage. A 0.1
μ
F electrolytic capacitor attached between VCOM and
AVSS. No load current may be drawn from MUTET. All signals, especially clocks, should be kept away from MUTET in
order to avoid unwanted coupling into the AK4220.
3. The notes for drawing the board
Analog input and output pins should be as short as possible in order to avoid unwanted coupling into the AK4220. The
unused pins should be open.
4. Video Output
The AK4220 has on-chip 3ch video amp for drive 150
Ω
resistance and two way to output video signal. One way is using
the Sag Compensation circuit (Figure 30), the other way is using DC output (Figure 31). 100
μ
F and 2.2
μ
F capacitors is
needed for Sag Compensation circuit . It should be shorted VOUT pin and VBF pin using DC output mode. The clamp
level is 600mV(typ) in the DC output mode. Each output way can set by SAGN bit (Table 13).
VOUT
R1
75
Ω
VFB
C3
100uF
C4
2.2uF
+6dB
R2
75
Ω
Figure 30. Video Block (SAGN bit=“0”, Sag Compensation mode)
VOUT
R1
75
Ω
VFB
+6dB
R2
75
Ω
Figure 31. Video Block (SAGN bit=“1”, DC Output)
SAGN bit
0
1
Output
Sag Compensation mode
DC output mode
(default)
Table 13. Setting for the video output
相關PDF資料 |
PDF描述 |
|---|---|
| AK4250 | Output Coupling Capacitor-less Video Amp with LPF |
| AK4250VU | Output Coupling Capacitor-less Video Amp with LPF |
| AK4252 | Output Coupling Capacitor-less Video Amp with LPF |
| AK4252VU | Output Coupling Capacitor-less Video Amp with LPF |
| AK4254 | Capacitor-less Video Amp with 7:2 Video Switch |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AK4223 | 制造商:AKM 制造商全稱:AKM 功能描述:6:2 Audio Switch and 6:2 Video Switch |
| AK4223VQ | 制造商:AKM 制造商全稱:AKM 功能描述:6:2 Audio Switch and 6:2 Video Switch |
| AK4250 | 制造商:AKM 制造商全稱:AKM 功能描述:1ch video amplifier with low pass filter |
| AK4250_10 | 制造商:AKM 制造商全稱:AKM 功能描述:Output Coupling Capacitor-less Video Amp with LPF |
| AK4250VT | 制造商:AKM 制造商全稱:AKM 功能描述:Output Coupling Capacitor-less Video Amp with LPF |
發布緊急采購，3分鐘左右您將得到回復。