- 您現在的位置：買賣IC網 > PDF目錄385090 > AK4182AVN (Asahi Kasei Microsystems Co.,Ltd) Touch Screen Controller PDF資料下載
參數資料
| 型號： | AK4182AVN |
| 廠商： | Asahi Kasei Microsystems Co.,Ltd |
| 英文描述： | Touch Screen Controller |
| 中文描述： | 觸摸屏控制器 |
| 文件頁數： | 7/18頁 |
| 文件大?。?/td> | 186K |
| 代理商： | AK4182AVN |
ASAHI KASEI
[AK4182A]
A/D Converter for Touch Screen
The AK4182A incorporates a 12-bit successive approximation resistor (SAR) A/D converter for position measurement,
temperature, and battery voltage. The architecture is based on capacitive redistribution algorithm, and an internal capacitor array
functions as the sample/hold (S/H) circuit.
The SAR A/D converter output is a straight binary format as shown below:
Input Voltage
(
VREF-1.5LSB)~
VREF
(
VREF-2.5LSB) ~ (
VREF-1.5LSB)
---------
0.5LSB ~ 1.5LSB
0 ~ 0.5LSB
VREF: (VREF+) – (VREF-)
MS0482-E-00
2006/03
7
Output Code
FFFH
FFEH
---------
001H
000H
Table 1 Output Code
The full scale (
VREF) of the A/D converter depends on the input mode. The AK4182A is controlled by the 8 bit serial command
on DIN.
Analog Inputs
Analog input is selected via the A2, A1, A0 and SER/ DFR bits in the control register. If the analog inputs are selected to the X
or Y-axis, SER/ DFR = “0”, which means differential mode, the full scale (
VREF) is the differential voltage between the non-
inverting terminal and the inverting terminal of the measured axis (e.g. X-axis measurement :(XP) – (XN)). Analog non-inverting
input to A/D converter is the non-inverting terminal of the non-measured axis while the inverting input is the inverting terminal of
the measured axis. If the SER/ DFR bit is set to “1” which means single-ended mode, the full scale of A/D converter (
VREF)
is the internal reference voltage or external reference voltage. Note that SER/ DFR bit should be set to”0” if IN2 is selected as
analog input; nevertheless, IN2 is actually measured by single-ended mode.
Tracking time is the period from the falling edge of 5
th
DCLK to that of 8
th
DCLK after the detection of START bit during
CSN=”L”.
The required settling time to charge the internal capacitor array depends on the source impedance (Rin). If the source impedance is
600
, the settling time needs at least 1.428
μ
s (3tDCLKat 2.1MHz). The maximum throughput of A/D converter is 125 kHz.
If the source impedance of analog input or battery input is larger than 600
, longer tracking time is required.
The Position Detection of Touch Screen
The position on the touch screen is detected by taking the voltage of one axis when the voltage is supplied between the two
terminals of another axis. At least two A/D conversions are needed to get the two-dimensional (X/Y axis) position.
相關PDF資料 |
PDF描述 |
|---|---|
| AK4182 | Touch Screen Controller |
| AK4182VN | Touch Screen Controller |
| AK4183 | I2C Touch Screen Controller |
| AK4183VT | I2C Touch Screen Controller |
| AK4184 | TSC with Keypad Scanner and GPIO Expander |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AK4182VN | 制造商:AKM 制造商全稱:AKM 功能描述:Touch Screen Controller |
| AK4183 | 制造商:AKM 制造商全稱:AKM 功能描述:I2C Touch Screen Controller |
| AK4183_08 | 制造商:AKM 制造商全稱:AKM 功能描述:I2C Touch Screen Controller |
| AK4183KT | 制造商:AKM 制造商全稱:AKM 功能描述:I2C Touch Screen Controller |
| AK4183VT | 制造商:AKM 制造商全稱:AKM 功能描述:I2C Touch Screen Controller |
發布緊急采購，3分鐘左右您將得到回復。