- 您現在的位置：買賣IC網 > PDF目錄385089 > AK2546 (Asahi Kasei Microsystems Co.,Ltd) 7 channel T1 Transceiver PDF資料下載
參數資料
| 型號： | AK2546 |
| 廠商： | Asahi Kasei Microsystems Co.,Ltd |
| 英文描述： | 7 channel T1 Transceiver |
| 中文描述： | 7頻道T1收發器 |
| 文件頁數： | 18/27頁 |
| 文件大?。?/td> | 123K |
| 代理商： | AK2546 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
ASAHI K ASEI [AK2546]
C0019-E-01 1999/9
18
STATUS REGISTER
Symbol
LOSx
(x=1 to 7)
LOTCx
(x=1 to 7)
LOMC
Description
Loss of signal alarm for channel x. Read only register.
When the loss of signal is detected, LOSx is set High.
Loss of TCLK alarm for channel x. Read only register.
When the loss of TCLKx is detected, LOTCx is set High.
Loss of MCLK alarm. Read only register.
When the loss of MCLK is detected, LOMC is set High.
MASK CONTROL
Symbol
MLOSx
(x=1 to 7)
Mask loss of signal alarm for channel x.
MLOSx is active-high to prevent LOSx from setting INT output “high”.
It is possible to read LOSx register regardless of the status of MLOSx.
Initial value is “high”.
Mask loss of TCLK alarm for channel x.
MLOTCx is active-high to prevent LOTCx from setting INT output “high”.
It is possible to read LOTCx register regardless of the status of MLOTCx.
Initial value is “high”.
Mask loss of MCLK alarm.
MLOMC is active-high to prevent LOMC from setting INT output “high”.
It is possible to read LOMC register regardless of the status of MLOMC.
Initial value is “high”. When the loss of MCLK is detected, LOSx register
and LOSx pins are set “high” at the same time. Therefore all MLOSx
register must be set “high” to prevent loss of MCLK from setting INT
output. In this case, LOMC can be read.
MLOTCx
(x=1 to 7)
MLOMC
CHANNEL CONTROL REGISTER
Symbol
LENGyx
Description
The generated transmit pulse in channel x provides the appropriate pulse
shape for line length from a DSX-1 cross connect through the setting of this
register as shown below in Table 1.
Loopback mode of channel x is activated through the setting of these
registers as shown below in Table 2.
This register as shown in Table 3 controls TIPx/RINGx output polarity.
Initial value is “high”.
PDx is active-high to set the corresponding transceiver in power down
mode.
The impedance between TTIP and TRING is set to 30k
(typ). LOSx goes
“high” in power down mode. Initial value is “high”.
MSK x is active-high to prevent LOSx or LOTCx from setting INT output
“high”. Initial value is “high”.
RDEN is active-high to prevent RCLK , RPOS, and RNEG output from
forcing to “l(fā)ow” or “high” by the detection of Loss of signal. Initial value is
“l(fā)ow”.
RLOOPx/
LLOOPx
POLNx
PDx
MSKx
RDEN
相關PDF資料 |
PDF描述 |
|---|---|
| AK2548 | 7 channel E1 Transceiver |
| AK2570 | Feed Forward APC LSI for LD Module |
| AK2572 | APC for Burst Mode Applicable Direct Modulation Laser Diode |
| AK2573A | 125M / 156M Laser Diode Driver + APC |
| AK2573AVB | 125M / 156M Laser Diode Driver + APC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AK2548 | 制造商:AKM 制造商全稱:AKM 功能描述:7 channel E1 Transceiver |
| AK2548A | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecommunication IC |
| AK2570 | 制造商:AKM 制造商全稱:AKM 功能描述:Feed Forward APC LSI for LD Module |
| AK2571 | 制造商:AKM 制造商全稱:AKM 功能描述:Single-Chip Automatic Power/Temperature Control for WDM Laser Diodes |
| AK2572 | 制造商:AKM 制造商全稱:AKM 功能描述:APC for Burst Mode Applicable Direct Modulation Laser Diode |
發布緊急采購，3分鐘左右您將得到回復。