- 您現在的位置：買賣IC網 > PDF目錄223321 > AFBR-57J5APZ FIBER OPTIC TRANSCEIVER, 830-860nm, 24576Mbps(Tx), 24576Mbps(Rx), BOARD/PANEL MOUNT, LC CONNECTOR PDF資料下載
參數資料
| 型號： | AFBR-57J5APZ |
| 元件分類： | 光收發 |
| 英文描述： | FIBER OPTIC TRANSCEIVER, 830-860nm, 24576Mbps(Tx), 24576Mbps(Rx), BOARD/PANEL MOUNT, LC CONNECTOR |
| 封裝： | ROHS COMPLIANT PACKAGE-20 |
| 文件頁數： | 11/18頁 |
| 文件大小： | 578K |
| 代理商： | AFBR-57J5APZ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁
2
Digital Diagnostic Interface and Serial Identification
The 2-wire serial interface is based on ATMEL AT24C01A
series EEPROM protocol and signaling detail. Conven-
tional EEPROM memory, bytes 0-255 at memory address
0xA0, is organized in compliance with INF-8074. New
digital diagnostic information, bytes 0-255 at memory
address 0xA2, is compliant to SFF-8472. The new diag-
nostic information provides the opportunity for Predic-
tive Failure Identification, Compliance Prediction, Fault
Isolation and Component Monitoring.
Transmitter Section
The transmitter section includes consists of the Transmit-
ter Optical SubAssembly (TOSA) and laser driver circuitry.
The TOSA, containing an 850nm VCSEL (Vertical Cavity
Surface Emitting Laser) light source, is located at the
optical interface and mates with the LC optical connector.
The TOSA is driven by a custom IC which uses the
incoming differential high speed logic signal to modulate
the laser diode driver current. This Tx laser driver circuit
regulates the optical power at a constant level provided
the incoming data pattern is dc balanced (8B/10B code,
for example).
Transmit Disable (Tx_Disable)
The AFBR-57J5APZ accepts a TTL and CMOS compatible
transmit disable control signal input (pin 3) which shuts
down the transmitter optical output. A high signal im-
plements this function while a low signal allows normal
transceiver operation. In the event of a fault (e.g. eye
safety circuit activated), cycling this control signal resets
the module as depicted in Figure 4. An internal pull up
resistor disables the transceiver transmitter until the host
pulls the input low. Host systems should allow a 10ms
interval between successive assertions of this control
signal. Tx_Disable can also be asserted via the two-
wire serial interface (address A2h, byte 110, bit 6) and
monitored (address A2h, byte 110, bit 7).
EEPROM
CONTROLLER
EEPROM
Photo-Detector
Amplification
&
Quantization
VCSEL
Laser Driver &
Safety Circuit
Electrical Interface
RD+ (Receive Data)
RD- (Receive Data)
Rx Loss Of Signal
MOD-DEF2 (SDA)
TX_DISABLE
TD+ (Transmit Data)
TD- (Transmit Data)
TX_FAULT
MOD-DEF0
MOD-DEF1 (SCL)
Receiver
Transmitter
Optical Interface
Light from Fiber
Light to Fiber
Rate Select
The contents of A2h, byte 110, bit 6 are logic OR’d with
hardware Tx_Disable (pin 3) to control transmitter
operation..
Transmit Fault (Tx_Fault)
A catastrophic laser fault will activate the transmitter
signal, TX_FAULT, and disable the laser. This signal is
an open collector output (pull-up required on the host
board). A low signal indicates normal laser operation
and a high signal indicates a fault. The TX_FAULT will
be latched high when a laser fault occurs and is cleared
by toggling the TX_DISABLE input or power cycling the
transceiver. The transmitter fault condition can also be
monitored via the two-wire serial interface (address A2,
byte 110, bit 2).
Eye Safety Circuit
The AFBR-57J5APZ provides Class 1 (single fault tolerant)
eye safety by design and has been tested for compliance
with the requirements listed in Table 1. The eye safety
circuit continuously monitors the optical output power
level and will disable the transmitter upon detecting an
unsafe condition beyond the scope of Class 1 certifica-
tion. Such unsafe conditions can be due to inputs from
the host board (Vcc fluctuation, unbalanced code) or a
fault within the transceiver.
Receiver Section
The receiver section includes the Receiver Optical Sub-
Assembly (ROSA) and the amplification/quantization
circuitry. The ROSA, containing a PIN photodiode and
custom transimpedance amplifier, is located at the
optical interface and mates with the LC optical connector.
The ROSA output is fed to a custom IC that provides post-
amplification and quantization.
Figure 1. Transceiver Functional Diagram
相關PDF資料 |
PDF描述 |
|---|---|
| AFBR-57R5AEZ | FIBER OPTIC TRANSCEIVER, 830-860nm, 4250Mbps(Tx), 4250Mbps(Rx), BOARD/PANEL MOUNT, LC CONNECTOR |
| AFBR-5803AQZ | FIBER OPTIC TRANSCEIVER, 1270-1380nm, 155Mbps(Tx), 155Mbps(Rx), BOARD/PANEL MOUNT, SIP, SC CONNECTOR |
| AFBR-5803ATQZ | FIBER OPTIC TRANSCEIVER, 1270-1380nm, 155Mbps(Tx), 155Mbps(Rx), BOARD/PANEL MOUNT, SIP, ST CONNECTOR |
| AFBR-5803TZ | FIBER OPTIC TRANSCEIVER, 1270-1380nm, 125Mbps(Tx), 125Mbps(Rx), THROUGH HOLE MOUNT, ST CONNECTOR |
| AFBR-5903EZ | FIBER OPTIC TRANSCEIVER, 1270-1380nm, 125Mbps(Tx), 125Mbps(Rx), BOARD/PANEL MOUNT, MT-RJ CONNECTOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AFBR-57J5APZ_13 | 制造商:AVAGO 制造商全稱:AVAGO TECHNOLOGIES LIMITED 功能描述:Digital Diagnostic SFP, 850nm 3.072/2.4576 Gb/s, RoHS OBSAI/CPRI Compatible Optical Transceiver |
| AFBR-57J5APZ-AX1 | 制造商:Avago Technologies 功能描述:3G MM BASE TRANSCEIVER STATION (BTS) SFP WITH DIGITAL DIAGNO - Trays |
| AFBR-57J7APZ | 功能描述:光纖發射器、接收器、收發器 7.37/6.14 Gb/s MMF SFP, Ind Temp RoHS:否 制造商:Omron Electronics 產品:Transmitters 數據速率:3.5 Gbps 波長:850 nm 最大工作溫度: 最小工作溫度: 封裝 / 箱體: 封裝: |
| AFBR-57J9AMZ | 制造商:Avago Technologies 功能描述:SFP+ 850NM 6GBE SR MMF, GEN 4 - Bulk 制造商:Avago Technologies 功能描述:TXRX MMF SFP 850NM 6GBE 制造商:Avago Technologies 功能描述:SFP+ 850nm 6GbE SR MMF, Gen 4 |
| AFBR-57L5APZ | 功能描述:光纖發射器、接收器、收發器 Transceiver RoHS:否 制造商:Omron Electronics 產品:Transmitters 數據速率:3.5 Gbps 波長:850 nm 最大工作溫度: 最小工作溫度: 封裝 / 箱體: 封裝: |
發布緊急采購，3分鐘左右您將得到回復。