- 您現在的位置：買賣IC網 > PDF目錄375269 > ADXL210AE (ANALOG DEVICES INC) Low-Cost 10 g Dual-Axis Accelerometer with Duty Cycle PDF資料下載
參數資料
| 型號： | ADXL210AE |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 模擬信號調理 |
| 英文描述： | Low-Cost 10 g Dual-Axis Accelerometer with Duty Cycle |
| 中文描述： | SPECIALTY ANALOG CIRCUIT, CQCC8 |
| 封裝： | CERAMIC, LCC-8 |
| 文件頁數： | 11/12頁 |
| 文件大?。?/td> | 169K |
| 代理商： | ADXL210AE |
REV. 0
ADXL210E
–11–
Power Cycling with an External A/D
Depending on the value of the X
FILT
capacitor, the ADXL210E
is capable of turning on and giving a good reading in 1.6 ms.
Most microcontroller-based A/Ds can acquire a reading in
another 25
μ
s. Thus it is possible to turn on the ADXL210E
and take a reading in <2 ms. If we assume that a 20 Hz sample
rate is sufficient, the total current required to take 20 samples is:
2
ms
20
Samples/s
0.6
mA =
24
μ
A
Running the part at 3 V will reduce the supply current from
0.6 mA to 0.4 mA, bringing the average current down to 16
μ
A.
The A/D should read the analog output of the ADXL210E at
the X
FILT
and Y
FILT
pins. A buffer amplifier is recommended, and
may be required in any case to amplify the analog output to give
enough resolution with an 8-bit to 10-bit converter.
Power Cycling When Using the Digital Output
An alternative is to run the microcontroller at a higher clock rate
and put it into shutdown between readings, allowing the use of the
digital output. In this approach the ADXL210E should be set at
its fastest sample rate (T2 = 0.5ms), with a 500 Hz filter at X
FILT
and Y
FILT
. The concept is to acquire a reading as quickly as
possible and then shut down the ADXL210E and the microcon-
troller until the next sample is needed.
In either of the above approaches, the ADXL210E can be turned
on and off directly using a digital port pin on the microcontroller to
power the accelerometer without additional components.
CALIBRATING THE ADXL210E
The initial value of the offset and scale factor for the ADXL210E will
require calibration for applications such as tilt measurement. The
ADXL210E architecture has been designed so that these calibra-
tions take place in the software of the microcontroller used to decode
the duty cycle signal. Calibration factors can be stored in EEPROM
or determined at turn-on and saved in dynamic memory.
For low
g
applications, the force of gravity is the most stable,
accurate and convenient acceleration reference available. A reading
of the 0
g
point can be determined by orientating the device
parallel to the earth
’
s surface and then reading the output.
A more accurate calibration method is to make measurements at
+1
g
and
–
1
g
. The sensitivity can be determined by the two
measurements.
To calibrate, the accelerometer
’
s measurement axis is pointed
directly at the earth. The 1
g
reading is saved and the sensor is
turned 180
°
to measure
–
1
g
. Using the two readings, the sensi-
tivity is:
Let A
=
Accelerometer output with axis oriented to
+1 g
Let B
=
Accelerometer output with axis oriented to
–
1 g
then
:
Sensitivity
= [A
–
B
]/2 g
For example, if the +1
g
reading (A) is 55% duty cycle and the
–
1
g
reading (B) is 47% duty cycle, then:
Sensitivity
= [55%
–
47%]/2 g = 4%/g
These equations apply whether the output is analog or duty cycle.
Application notes outlining algorithms for calculating accelera-
tion from duty cycle and automated calibration routines are
available from the factory.
Table V. Trade-Offs Between Microcontroller Counter Rate,
T2 Period, and Resolution of Duty Cycle Modulator
Counter-
ADXL210E Clock
R
SET
Sample
T2 (ms) (k ) Rate
Counts
per T2
Cycle
Rate
(MHz)
Counts Resolution
per
g
(m
g
)
1.0
1.0
1.0
5.0
5.0
5.0
10.0
10.0
10.0
124
124
124
625
625
625
1250 100
1250 100
1250 100
1000
1000
1000
200
200
200
2.0
1.0
0.5
2.0
1.0
0.5
2.0
1.0
0.5
2000
1000
500
10000
5000
2500
20000
10000
5000
80
40
20
400
200
100
800
400
200
12.50
25.00
50.00
2.50
5.00
10.00
1.25
2.50
5.00
USING THE ANALOG OUTPUT
The ADXL210E was specifically designed for use with its digital
outputs, but has provisions to provide analog outputs as well.
Duty Cycle Filtering
An analog output can be reconstructed by filtering the duty cycle
output. This technique requires only passive components. The
duty cycle period (T2) should be set to <1 ms. An RC filter with a
3 dB point at least a factor of >10 less than the duty cycle fre-
quency is connected to the duty cycle output. The filter resistor
should be no less than 100 k
to prevent loading of the output
stage. The analog output signal will be ratiometric to the supply
voltage. The advantage of this method is an output scale factor of
approximately double the analog output. Its disadvantage is that
the frequency response will be lower than when using the X
FILT
,
Y
FILT
output.
X
FILT
, Y
FILT
Output
The second method is to use the analog output present at the
X
FILT
and Y
FILT
pin. Unfortunately, these pins have a 32 k
output impedance and are not designed to drive a load directly.
An op amp follower may be required to buffer this pin. The
advantage of this method is that the full 5 kHz bandwidth of the
accelerometer is available to the user. A capacitor still must be
added at this point for filtering. The duty cycle converter should
be kept running by using R
SET
<10 M
. Note that the acceler-
ometer offset and sensitivity are ratiometric to the supply voltage.
The offset and sensitivity are nominally:
0 g
Offset
=
V
DD
/2
ADXL210E Sensitivity
= (20
mV
V
S
)/g
USING THE ADXL210E IN VERY LOW POWER
APPLICATIONS
An application note outlining low power strategies for the
ADXL210E is available. Some key points are presented here.
It is possible to reduce the ADXL210E
’
s average current from
0.6 mA to less than 20
μ
A by using the following techniques:
1. Power cycle the accelerometer.
2. Run the accelerometer at a lower voltage (down to 3 V).
相關PDF資料 |
PDF描述 |
|---|---|
| ADXL210JE | Low-Cost 10 g Dual-Axis Accelerometer with Duty Cycle |
| ADXL213 | Low Cost 1.2 g Dual Axis Accelerometer |
| ADXL213AE-REEL | Low Cost 1.2 g Dual Axis Accelerometer |
| ADXL213AE | Low Cost 1.2 g Dual Axis Accelerometer |
| ADXL213EB | Low Cost 1.2 g Dual Axis Accelerometer |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADXL210AE-REEL | 功能描述:IC ACCELER DUAL-AX 10G 8CLCC RoHS:是 類別:傳感器，轉換器 >> 加速計 系列:- 標準包裝:1 系列:SCA1000 軸:X，Y 加速范圍:±1.7g 靈敏度:1.2V/g 電源電壓:4.75 V ~ 5.25 V 輸出類型:數字 帶寬:50±30Hz 接口:SPI 安裝類型:表面貼裝 封裝/外殼:12-SMD 供應商設備封裝:12-SMD 其它名稱:551-1007-1 |
| ADXL210AQC | 制造商:Analog Devices 功能描述:ACCELERATION DETECTOR, 14 Pin, Ceramic, SOP |
| ADXL210AQC-1 | 制造商:Analog Devices 功能描述: |
| ADXL210E | 制造商:AD 制造商全稱:Analog Devices 功能描述:Low-Cost 10 g Dual-Axis Accelerometer with Duty Cycle |
| ADXL210EB | 制造商:Analog Devices 功能描述:Evaluation Board For ADXL210 制造商:Analog Devices 功能描述:SEMICONDUCTOR ((NW)) |
發布緊急采購，3分鐘左右您將得到回復。