- 您現在的位置：買賣IC網 > PDF目錄374048 > ADXL210 (Analog Devices, Inc.) Circular Connector; MIL SPEC:MIL-DTL-38999 Series I; Body Material:Metal; Series:LJT; No. of Contacts:100; Connector Shell Size:23; Connecting Termination:Crimp; Circular Shell Style:Wall Mount Receptacle; Body Style:Straight RoHS Compliant: No PDF資料下載
參數資料
| 型號： | ADXL210 |
| 廠商： | Analog Devices, Inc. |
| 元件分類： | 圓形連接器 |
| 英文描述： | Circular Connector; MIL SPEC:MIL-DTL-38999 Series I; Body Material:Metal; Series:LJT; No. of Contacts:100; Connector Shell Size:23; Connecting Termination:Crimp; Circular Shell Style:Wall Mount Receptacle; Body Style:Straight RoHS Compliant: No |
| 中文描述： | 低成本-2克/ -10克雙主軸與數字輸出加速計 |
| 文件頁數： | 7/11頁 |
| 文件大?。?/td> | 124K |
| 代理商： | ADXL210 |
ADXL202/ADXL210
–7–
REV. B
Setting the Bandwidth Using C
X
and C
Y
The ADXL202/ADXL210 have provisions for bandlimiting the
X
FILT
and Y
FILT
pins. Capacitors must be added at these pins to
implement low-pass filtering for antialiasing and noise reduc-
tion. The equation for the 3 dB bandwidth is:
F
–3
dB
=
1
2
π
(32
k
)
×
C
(
x
,
y
)
(
)
or, more simply,
F
–3
dB
=
5
μ
F
C
(
X
,
Y
)
The tolerance of the internal resistor (R
FILT
), can vary as much
as
±
25% of its nominal value of 32 k
; so the bandwidth will
vary accordingly. A minimum capacitance of 1000 pF for C
(X, Y)
is required in all cases.
Table I. Filter Capacitor Selection, C
X
and C
Y
Capacitor
Value
0.47
μ
F
0.10
μ
F
0.05
μ
F
0.027
μ
F
0.01
μ
F
0.001
μ
F
Bandwidth
10 Hz
50 Hz
100 Hz
200 Hz
500 Hz
5 kHz
Setting the DCM Period with R
SET
The period of the DCM output is set for both channels by a
single resistor from R
SET
to ground. The equation for the period
is:
T
2
=
R
SET
(
)
125
M
A 125 k
resistor will set the duty cycle repetition rate to ap-
proximately 1 kHz, or 1 ms. The device is designed to operate at
duty cycle periods between 0.5 ms and 10 ms.
Table II. Resistor Values to Set T2
T2
R
SET
125 k
250 k
625 k
1.25 M
1 ms
2 ms
5 ms
10 ms
Note that the R
SET
should always be included, even if only an
analog output is desired. Use an R
SET
value between 500 k
and 2 M
when taking the output from X
FILT
or Y
FILT
. The
R
SET
resistor should be place close to the T2 Pin to minimize
parasitic capacitance at this node.
Selecting the Right Accelerometer
For most tilt sensing applications the ADXL202 is the most
appropriate accelerometer. Its higher sensitivity (12.5%/
g
allows
the user to use a lower speed counter for PWM decoding while
maintaining high resolution. The ADXL210 should be used in
applications where accelerations of greater than
±
2
g
are expected.
MICROCOMPUTER INTERFACES
The ADXL202/ADXL210 were specifically designed to work
with low cost microcontrollers. Specific code sets, reference
designs, and application notes are available from the factory.
This section will outline a general design procedure and discuss
the various trade-offs that need to be considered.
The designer should have some idea of the required perfor-
mance of the system in terms of:
Resolution
: the smallest signal change that needs to be detected.
Bandwidth
: the highest frequency that needs to be detected.
Acquisition Time
: the time that will be available to acquire the
signal on each axis.
These requirements will help to determine the accelerometer
bandwidth, the speed of the microcontroller clock and the
length of the T2 period.
When selecting a microcontroller it is helpful to have a counter
timer port available. The microcontroller should have provisions
for software calibration. While the ADXL202/ADXL210 are
highly accurate accelerometers, they have a wide tolerance for
DEMOD
R
FILT
32k
V
R
FILT
32k
V
OSCILLATOR
X SENSOR
Y SENSOR
X OUT
Y OUT
SELF TEST
X
FILT
V
DD
V
DD
C
X
+3.0V TO +5.25V
C
DC
COM
Y
FILT
T2
C
Y
R
SET
C
O
U
N
T
E
R
m
P
T2
A(g) = (T1/T2 – 0.5)/12.5%
0g= 50% DUTY CYCLE
T2 = R
SET
/125M
V
T1
DEMOD
DUTY
CYCLE
MODULATOR
(DCM)
ADXL202/
ADXL210
Figure 13. Block Diagram
相關PDF資料 |
PDF描述 |
|---|---|
| ADXL210AQC | Circular Connector; No. of Contacts:100; Series:LJTPQ00R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:23; Circular Contact Gender:Socket; Circular Shell Style:Wall Mount Receptacle |
| ADXL210JQC | Circular Connector; MIL SPEC:MIL-DTL-38999 Series I; Body Material:Metal; Series:LJT; No. of Contacts:53; Connector Shell Size:23; Connecting Termination:Crimp; Circular Shell Style:Wall Mount Receptacle; Body Style:Straight RoHS Compliant: No |
| ADXL210JQC-1 | Low Cost 62 g/610 g Dual Axis Accelerometers with Digital Output(124.95 k) |
| ADXL203 | Circular Connector; MIL SPEC:MIL-DTL-38999 Series I; Body Material:Metal; Series:LJT; No. of Contacts:16; Connector Shell Size:21; Connecting Termination:Crimp; Circular Shell Style:Wall Mount Receptacle; Body Style:Straight RoHS Compliant: No |
| ADXL203CE-REEL1 | Circular Connector; No. of Contacts:16; Series:LJTPQ00R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:21; Circular Contact Gender:Socket; Circular Shell Style:Wall Mount Receptacle |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADXL210AE | 制造商:Analog Devices 功能描述:Accelerometer Dual 制造商:Analog Devices 功能描述:ICAcceleration DetectorBICMOSLLCC8PI |
| ADXL210AE-REEL | 功能描述:IC ACCELER DUAL-AX 10G 8CLCC RoHS:是 類別:傳感器，轉換器 >> 加速計 系列:- 標準包裝:1 系列:SCA1000 軸:X，Y 加速范圍:±1.7g 靈敏度:1.2V/g 電源電壓:4.75 V ~ 5.25 V 輸出類型:數字 帶寬:50±30Hz 接口:SPI 安裝類型:表面貼裝 封裝/外殼:12-SMD 供應商設備封裝:12-SMD 其它名稱:551-1007-1 |
| ADXL210AQC | 制造商:Analog Devices 功能描述:ACCELERATION DETECTOR, 14 Pin, Ceramic, SOP |
| ADXL210AQC-1 | 制造商:Analog Devices 功能描述: |
| ADXL210E | 制造商:AD 制造商全稱:Analog Devices 功能描述:Low-Cost 10 g Dual-Axis Accelerometer with Duty Cycle |
發布緊急采購，3分鐘左右您將得到回復。