參數資料
型號： ADV7180KCP32Z
廠商： Analog Devices Inc
文件頁數： 41/116頁
文件大?。?/td> 0K
描述： IC VIDEO DECODER 10BIT 32LFCSP
設計資源： Low Cost Differential Video Receiver Using ADA4851 Amplifier and ADV7180 Video Decoder (CN0060)
Low Cost Video Multiplexer for Video Switching Using ADA4853-2 Op Amp with Disable Function (CN0076)
標準包裝： 1
類型： 視頻解碼器
應用： 數碼相機，手機，便攜式視頻
安裝類型： 表面貼裝
封裝/外殼： 32-WFQFN 裸露焊盤，CSP
供應商設備封裝： 32-LFCSP-WQ（5x5）
包裝： 托盤
ADV7180
Data Sheet
Rev. I | Page 30 of 116
SD_OFF_Cb[7:0], SD Offset Cb Channel, Address 0xE1[7:0]
This register allows the user to select an offset for the Cb channel
only and to adjust the hue of the picture. There is a functional
overlap with the HUE[7:0] register.
Table 30. SD_OFF_Cb Function
SD_OFF_Cb[7:0]
Description
0x80 (default)
0 mV offset applied to the Cb channel
0x00
312 mV offset applied to the Cb channel
0xFF
+312 mV offset applied to the Cb channel
SD_OFF_Cr[7:0], SD Offset Cr Channel, Address 0xE2[7:0]
This register allows the user to select an offset for the Cr channel
only and to adjust the hue of the picture. There is a functional
overlap with the HUE[7:0] register.
Table 31. SD_OFF_Cr Function
SD_OFF_Cr[7:0]
Description
0x80 (default)
0 mV offset applied to the Cr channel
0x00
312 mV offset applied to the Cr channel
0xFF
+312 mV offset applied to the Cr channel
BRI[7:0], Brightness Adjust, Address 0x0A[7:0]
This register controls the brightness of the video signal. It allows
the user to adjust the brightness of the picture.
Table 32. BRI Function
BRI[7:0]
Description
0x00 (default)
Offset of the luma channel = 0 IRE
0x7F
Offset of the luma channel = +30 IRE
0x80
Offset of the luma channel = 30 IRE
HUE[7:0], Hue Adjust, Address 0x0B[7:0]
This register contains the value for the color hue adjustment. It
allows the user to adjust the hue of the picture.
HUE[7:0] has a range of ±90°, with 0x00 equivalent to an
adjustment of 0°. The resolution of HUE[7:0] is 1 bit = 0.7°.
The hue adjustment value is fed into the AM color demodulation
block. Therefore, it applies only to video signals that contain
chroma information in the form of an AM-modulated carrier
(CVBS or Y/C in PAL or NTSC). It does not affect SECAM
and does not work on component video inputs (YPrPb).
Table 33. HUE Function
HUE[7:0]
Description (Adjust Hue of the Picture)
0x00 (default)
Phase of the chroma signal = 0°
0x7F
Phase of the chroma signal = 90°
0x80
Phase of the chroma signal = +90°
DEF_Y[5:0], Default Value Y, Address 0x0C[7:2]
When the ADV7180 loses lock on the incoming video signal or
when there is no input signal, the DEF_Y[5:0] register allows
the user to specify a default luma value to be output. This value
is used under the following conditions:
If the DEF_VAL_AUTO_EN bit is set to high and the
ADV7180 has lost lock to the input video signal. This is
the intended mode of operation (automatic mode).
The DEF_VAL_EN bit is set, regardless of the lock status of
the video decoder. This is a forced mode that may be useful
during configuration.
The DEF_Y[5:0] values define the six MSBs of the output video.
The remaining LSBs are padded with 0s. For example, in 8-bit
mode, the output is Y[7:0] = {DEF_Y[5:0], 0, 0}.
For DEF_Y[5:0], 0x0D (blue) is the default value for Y.
Register 0x0C has a default value of 0x36.
DEF_C[7:0], Default Value C, Address 0x0D[7:0]
The DEF_C[7:0] register complements the DEF_Y[5:0] value. It
defines the four MSBs of Cr and Cb values to be output if
The DEF_VAL_AUTO_EN bit is set to high and the
ADV7180 cannot lock to the input video (automatic mode).
DEF_VAL_EN bit is set to high (forced output).
The data that is finally output from the ADV7180 for the
chroma side is Cr[3:0] = {DEF_C[7:4], 0, 0, 0, 0}, and
Cb[3:0] = {DEF_C[3:0], 0, 0, 0, 0}.
For DEF_C[7:0], 0x7C (blue) is the default value for Cr and Cb.
DEF_VAL_EN, Default Value Enable, Address 0x0C[0]
This bit forces the use of the default values for Y, Cr, and Cb. See
sections for additional information. In this mode, the decoder
also outputs a stable 27 MHz clock, HS, and VS.
Setting DEF_VAL_EN to 0 (default) outputs a colored screen
determined by user-programmable Y, Cr, and Cb values when
the decoder free-runs. Free-run mode is turned on and off by
the DEF_VAL_AUTO_EN bit.
Setting DEF_VAL_EN to 1 forces a colored screen output
determined by user-programmable Y, Cr, and Cb values.
This overrides picture data even if the decoder is locked.
相關PDF資料
PDF描述
ADV7180BCPZ-REEL IC VIDEO DECODER SDTV 40-LFCSP
VE-B7P-MX-F2 CONVERTER MOD DC/DC 13.8V 75W
VE-B7P-MX-F1 CONVERTER MOD DC/DC 13.8V 75W
VE-B7P-MW CONVERTER MOD DC/DC 13.8V 100W
PT02A-12-3P CONN RECEPT 3POS W/PINS SOLDER
相關代理商/技術參數
參數描述
ADV7180KCP32Z-RL 功能描述:IC VIDEO DECODER 10BIT 32LFCSP RoHS:是 類別:集成電路 (IC) >> 線性 - 視頻處理 系列:- 產品變化通告:Product Discontinuation 07/Mar/2011 標準包裝:3,000 系列:OMNITUNE™ 類型:調諧器 應用:移動電話，手機，視頻顯示器 安裝類型:表面貼裝 封裝/外殼:65-WFBGA 供應商設備封裝:PG-WFSGA-65 包裝:帶卷 (TR) 其它名稱:SP000365064
ADV7180KST48Z 功能描述:IC VID DECOD SDTV 10BIT 48LQFP RoHS:是 類別:集成電路 (IC) >> 線性 - 視頻處理 系列:- 產品變化通告:Product Discontinuation 07/Mar/2011 標準包裝:3,000 系列:OMNITUNE™ 類型:調諧器 應用:移動電話，手機，視頻顯示器 安裝類型:表面貼裝 封裝/外殼:65-WFBGA 供應商設備封裝:PG-WFSGA-65 包裝:帶卷 (TR) 其它名稱:SP000365064
ADV7180KST48Z-RL 功能描述:視頻 IC 48-Lead Low Profile Quad Flat Package RoHS:否 制造商:Fairchild Semiconductor 工作電源電壓:5 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-28 封裝:Reel
ADV7180WBCP32Z 制造商:Analog Devices 功能描述:IC, 10-BIT 4X OVERSAMPLING SDTV DECODER 制造商:Analog Devices 功能描述:SDTV VIDEO DECODER 32-PIN LFCSP EP TRAY - Trays
ADV7180WBCP32Z-RL 制造商:Analog Devices 功能描述:10-BIT, 4? OVERSAMPLING SDTV VIDEO DECODER - Tape and Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*