- 您現在的位置：買賣IC網 > PDF目錄374044 > ADV3000ASTZ-RL (ANALOG DEVICES INC) 3:1 HDMI/DVI Switch with Equalization PDF資料下載
參數資料
| 型號： | ADV3000ASTZ-RL |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 消費家電 |
| 英文描述： | 3:1 HDMI/DVI Switch with Equalization |
| 中文描述： | SPECIALTY CONSUMER CIRCUIT, PQFP80 |
| 封裝： | 14 X 14 MM, LEAD FREE, MS-026BEC, LQFP-80 |
| 文件頁數： | 13/28頁 |
| 文件大?。?/td> | 608K |
| 代理商： | ADV3000ASTZ-RL |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
ADV3000
The ADV3000 requires output termination resistors when the
high speed outputs are enabled. Termination can be internal
and/or external. The internal terminations of the ADV3000
are enabled by programming the TX_PTO bit of the transmitter
settings register. These terminations are always enabled in
parallel control mode.
External terminations can be provided either by on-board
resistors or by the input termination resistors of an HDMI/
DVI receiver. If both the internal terminations are enabled and
external terminations are present, set the output current level to
20 mA by programming the TX_OCL bit of the transmitter
settings register through the serial control interface or by setting
the PP_OCL pin of the parallel control interface. The output
current level defaults to the level indicated by PP_OCL upon
reset. If only external terminations are provided (if the internal
terminations are disabled), set the output current level to 10 mA
by programming the TX_OCL bit of the transmitter settings
register or by setting the PP_OCL pin of the parallel control
interface. The high speed outputs must be disabled if there are
no output termination resistors present in the system.
The output pre-emphasis can be manually configured to provide
one of four different levels of high frequency boost. The specific
boost level is selected by programming the TX_PE bits of the
transmitter settings register through the serial control interface,
or by setting the PP_PE bus of the parallel control interface. No
specific cable length is suggested for a particular pre-emphasis
setting because cable performance varies widely between
manufacturers.
AUXILIARY SWITCH
The auxiliary (low speed) lines have no amplification. They are
routed using a passive switch that is bandwidth compatible with
standard speed I
2
C. The schematic equivalent for this passive
connection is shown in Figure 27.
Rev. 0 | Page 13 of 28
AUX_COM0
AUX_A0
C
AUX
C
AUX
R
AUX
0
Figure 27. Auxiliary Channel Simplified Schematic,
AUX_A0 to AUX_COM0 Routing Example
When turning off the ADV3000, care needs to be taken with
the AMUXVCC supply to ensure that the auxiliary multiplexer
pins remain in a high impedance state. A scenario that illustrates
this requirement is one where the auxiliary multiplexer is used
to switch the display data channel (DDC) bus. In some applica-
tions, additional devices can be connected to the DDC bus
(such as an EEPROM with EDID information) upstream of
the ADV3000. Extended display identification data (EDID)
is a VESA standard-defined data format for conveying display
configuration information to sources to optimize display use.
EDID devices may need to be available via the DDC bus, regard-
less of the state of the ADV3000 and any downstream circuit.
For this configuration, the auxiliary inputs of the powered
down ADV3000 need to be in a high impedance state to avoid
pulling down on the DDC lines and preventing these other
devices from using the bus.
When the ADV3000 is powered from a simple resistor network,
as shown in Figure 28, it uses the 5 V supply that is required
from any HDMI/DVI source to guarantee high impedance of
the auxiliary multiplexer pins. The AMUXVCC supply does not
draw any static current; therefore, it is recommended that the
resistor network tap the 5 V supplies as close to the connectors
as possible to avoid any additional voltage drop.
This precaution does not need to be taken if the DDC
peripheral circuitry is connected to the bus downstream of
the ADV3000.
PERIPHERAL
CIRCUITRY
+5V SOURCE C
PIN 18 HDMI CONNECTOR
PIN 14 DVI CONNECTOR
10k
10M
I<50mA
PERIPHERAL
CIRCUITRY
PERIPHERAL
CIRCUITRY
SOURCE A +5V
SOURCE B +5V
PIN 18 HDMI CONNECTOR
PIN 14 DVI CONNECTOR
PIN 18 HDMI CONNECTOR
PIN 14 DVI CONNECTOR
Figure 28. Suggested AMUXVCC Power Scheme
10k
10k
I<50mA
I<50mA
AMUXVCC
ADV3000
+5V INTERNAL
(IF ANY)
0
相關PDF資料 |
PDF描述 |
|---|---|
| ADV3000-EVALZ | 3:1 HDMI/DVI Switch with Equalization |
| ADV453 | Circular Connector; No. of Contacts:22; Series:LJTP02R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:13; Circular Contact Gender:Socket; Circular Shell Style:Box Mount Receptacle |
| ADV458 | Triple 8-Bit Video RAM-DAC(三通道,8位視頻RAM-D/A轉換器) |
| ADV476KP35 | CMOS Monolithic 256x18 Color Palette RAM-DAC |
| ADV476KP50 | CMOS Monolithic 256x18 Color Palette RAM-DAC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADV3000-EVALZ | 制造商:Analog Devices 功能描述:EVAL KIT FOR 3:1 HDMI/DVI SWIT W/ EQUALIZATION - Bulk |
| ADV3002 | 制造商:AD 制造商全稱:Analog Devices 功能描述:4:1 HDMI/DVI Switch with Equalization, DDC/CEC Buffers and EDID Replication |
| ADV3002BSTZ | 功能描述:IC SWITCH HDMI/DVI 4:1 80LQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 應用說明:Ultrasound Imaging Systems Application Note 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:250 系列:- 功能:開關 電路:單刀單擲 導通狀態電阻:48 歐姆 電壓電源:單電源 電壓 - 電源，單路/雙路(±):2.7 V ~ 5.5 V 電流 - 電源:5µA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:48-LQFP 供應商設備封裝:48-LQFP（7x7） 包裝:托盤 |
| ADV3002BSTZ-RL | 功能描述:IC SWITCH HDMI/DVI 4:1 80-LQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 其它有關文件:STG4159 View All Specifications 標準包裝:5,000 系列:- 功能:開關 電路:1 x SPDT 導通狀態電阻:300 毫歐 電壓電源:雙電源 電壓 - 電源，單路/雙路(±):±1.65 V ~ 4.8 V 電流 - 電源:50nA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:7-WFBGA，F(xiàn)CBGA 供應商設備封裝:7-覆晶 包裝:帶卷 (TR) |
| ADV3002-EVALZ | 制造商:AD 制造商全稱:Analog Devices 功能描述:4:1 HDMI/DVI Switch with Equalization, DDC/CEC Buffers and EDID Replication |
發布緊急采購，3分鐘左右您將得到回復。