- 您現在的位置：買賣IC網 > PDF目錄12016 > ADUC847BSZ62-5 (Analog Devices Inc)IC FLASH MCU W/24BIT ADC 52-MQFP PDF資料下載
參數資料
| 型號： | ADUC847BSZ62-5 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 46/108頁 |
| 文件大小： | 0K |
| 描述： | IC FLASH MCU W/24BIT ADC 52-MQFP |
| 產品培訓模塊： | Process Control |
| 標準包裝： | 1 |
| 系列： | MicroConverter® ADuC8xx |
| 核心處理器： | 8052 |
| 芯體尺寸： | 8-位 |
| 速度： | 12.58MHz |
| 連通性： | I²C，SPI，UART/USART |
| 外圍設備： | POR，PSM，PWM，溫度傳感器，WDT |
| 輸入/輸出數： | 34 |
| 程序存儲器容量： | 62KB（62K x 8） |
| 程序存儲器類型： | 閃存 |
| EEPROM 大小： | 4K x 8 |
| RAM 容量： | 2.25K x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 4.75 V ~ 5.25 V |
| 數據轉換器： | A/D 10x24b; D/A 1x12b，2x16b |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 125°C |
| 封裝/外殼： | 52-QFP |
| 包裝： | 托盤 |
| 產品目錄頁面： | 738 (CN2011-ZH PDF) |
| 配用： | EVAL-ADUC847QSZ-ND - KIT DEV QUICK START FOR ADUC847 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁當前第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁
ADuC845/ADuC847/ADuC848
Data Sheet
Rev. C | Page 42 of 108
Notes on the ADCMODE Register
Any change to the MD bits immediately resets both ADCs
(auxiliary ADC only applicable to the ADuC845). A write
to the MD2–MD0 bits with no change in contents is also
treated as a reset. (See the exception to this in the third
note of this section.)
If ADC1CON1 and ADC1CON2 are written when
ADC0EN = 1, or if ADC0EN is changed from 0 to 1, both
ADCs are also immediately reset. In other words, the
primary ADC is given priority over the auxiliary ADC and
any change requested on the primary ADC is immediately
responded to. Only applicable to the ADuC845.
On the other hand, if ADC1CON is written to or if
ADC1EN is changed from 0 to 1, only the auxiliary ADC
is reset. For example, if the primary ADC is continuously
converting when the auxiliary ADC change or enable
occurs, the primary ADC continues undisturbed. Rather
than allow the auxiliary ADC to operate with a phase
difference from the primary ADC, the auxiliary ADC falls
into step with the outputs of the primary ADC. The result
is that the first conversion time for the auxiliary ADC is
delayed by up to three outputs while the auxiliary ADC
update rate is synchronized to the primary ADC. Only
applicable to ADuC845. If the ADC1CON write occurs
after the primary ADC has completed its operation, the
auxiliary ADC can respond immediately without having to
fall into step with the primary ADCs output cycle.
If the parts are powered down via the PD bit in the PCON
register, the current ADCMODE bits are preserved, that is,
they are not reset to default state. Upon a subsequent
resumption of normal operating mode, the ADCs restarts
the selected operation defined by the ADCMODE register.
Once ADCMODE has been written with a calibration
mode, the RDY0/1 (ADuC845 only) bits (ADCSTAT) are
reset and the calibration commences. On completion, the
appropriate calibration registers are written, the relevant
bits in ADCSTAT are written, and the MD2–MD0 bits are
reset to 000B to indicate that the ADC is back in power-
down mode.
Any calibration request of the auxiliary ADC while the
temperature sensor is selected fails to complete. Although
the RDY1 bit is set at the end of the calibration cycle, no
update of the calibration SFRs takes place, and the ERR1
bit is set. ADuC845 only.
Calibrations performed at maximum SF (see Table 28)
value (slowest ADC throughput rate) help to ensure
optimum calibration.
The duration of a calibration cycle is 2/Fadc for chop-on
mode and 4/Fadc for chop-off mode.
相關PDF資料 |
PDF描述 |
|---|---|
| VJ1825Y333JBGAT4X | CAP CER 0.033UF 1KV 5% X7R 1825 |
| VJ2220Y684KBCAT4X | CAP CER 0.68UF 200V 10% X7R 2220 |
| VI-JTV-IY-F3 | CONVERTER MOD DC/DC 5.8V 50W |
| VI-JTT-IY-F1 | CONVERTER MOD DC/DC 6.5V 50W |
| VI-JTR-IY-F3 | CONVERTER MOD DC/DC 7.5V 50W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADUC847BSZ8-3 | 功能描述:IC MCU FLASH W/24BIT ADC 52MQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND |
| ADUC847BSZ8-5 | 功能描述:IC MCU FLASH W/24BIT ADC 52MQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND |
| ADUC848 | 制造商:AD 制造商全稱:Analog Devices 功能描述:MicroConverter Multichannel 24-/16-Bit ADCs with Embedded 62 kB Flash and Single-Cycle MCU |
| ADUC848BCP32-3 | 制造商:Analog Devices 功能描述:10 CHANNEL 16 BIT ADC + FLASH 8 BIT UP - Trays |
| ADUC848BCP32-5 | 制造商:Analog Devices 功能描述:10 CHANNEL 16 BIT ADC + FLASH 8 BIT UP - Trays |
發布緊急采購，3分鐘左右您將得到回復。