參數資料
型號： ADUC7029BBCZ62I
廠商： Analog Devices Inc
文件頁數： 64/104頁
文件大?。?/td> 0K
描述： IC MCU 12BIT 62KB FLASH 49BGA
標準包裝： 1
系列： MicroConverter® ADuC7xxx
核心處理器： ARM7
芯體尺寸： 16/32-位
速度： 44MHz
連通性： EBI/EMI，I²C，SPI，UART/USART
外圍設備： PLA，PWM，PSM，溫度傳感器，WDT
輸入/輸出數： 22
程序存儲器容量： 64KB（32K x 16）
程序存儲器類型： 閃存
RAM 容量： 2K x 32
電壓 - 電源 (Vcc/Vdd)： 2.7 V ~ 3.6 V
數據轉換器： A/D 7x12b，D/A 4x12b
振蕩器型： 內部
工作溫度： -40°C ~ 125°C
封裝/外殼： 49-TFBGA，CSPBGA
包裝： 托盤
ADuC7019/20/21/22/24/25/26/27/28/29
Data Sheet
Rev. F | Page 62 of 104
DESCRIPTION OF THE PWM BLOCK
A functional block diagram of the PWM controller is shown in
Figure 68. The generation of the six output PWM signals on
Pin PWM0H to Pin PWM2L is controlled by the following four
important blocks:
The 3-phase PWM timing unit. The core of the PWM
controller, this block generates three pairs of complemented
and dead-time-adjusted, center-based PWM signals. This
unit also generates the internal synchronization pulse,
PWMSYNC. It also controls whether the external PWMSYNC
pin is used.
The output control unit. This block can redirect the
outputs of the 3-phase timing unit for each channel to
either the high-side or low-side output. In addition, the
output control unit allows individual enabling/disabling
of each of the six PWM output signals.
The gate drive unit. This block can generate the high
frequency chopping and its subsequent mixing with the
PWM signals.
The PWM shutdown controller. This block controls the
PWM shutdown via the PWMTRIP pin and generates the
correct reset signal for the timing unit.
The PWM controller is driven by the ADuC7019/20/21/22/24/
25/26/27/28/29 core clock frequency and is capable of generating
two interrupts to the ARM core. One interrupt is generated on
the occurrence of a PWMSYNC pulse, and the other is
generated on the occurrence of any PWM shutdown action.
3-Phase Timing Unit
PWM Switching Frequency (PWMDAT0 MMR)
The PWM switching frequency is controlled by the PWM
period register, PWMDAT0. The fundamental timing unit
of the PWM controller is
tCORE = 1/fCORE
where fCORE is the core frequency of the MicroConverter.
Therefore, for a 41.78 MHz fCORE, the fundamental time increment
is 24 ns. The value written to the PWMDAT0 register is effectively
the number of fCORE clock increments in one-half a PWM
period. The required PWMDAT0 value is a function of the
desired PWM switching frequency (fPWN) and is given by
PWMDAT0 = fCORE/(2 × fPWM)
Therefore, the PWM switching period, tS, can be written as
tS = 2 × PWMDAT0 × tCORE
The largest value that can be written to the 16-bit PWMDAT0
MMR is 0xFFFF = 65,535, which corresponds to a minimum
PWM switching frequency of
fPWM(min) = 41.78 × 106/(2 × 65,535) = 318.75 Hz
Note that PWMDAT0 values of 0 and 1 are not defined and
should not be used.
PWM Switching Dead Time (PWMDAT1 MMR)
The second important parameter that must be set up in the initial
configuration of the PWM block is the switching dead time. This
is a short delay time introduced between turning off one PWM
signal (0H, for example) and turning on the complementary
signal (0L). This short time delay is introduced to permit the
power switch to be turned off (in this case, 0H) to completely
recover its blocking capability before the complementary switch is
turned on. This time delay prevents a potentially destructive
short-circuit condition from developing across the dc link
capacitor of a typical voltage source inverter.
The dead time is controlled by the 10-bit, read/write PWMDAT1
register. There is only one dead-time register that controls the dead
time inserted into all three pairs of PWM output signals. The dead
time, tD, is related to the value in the PWMDAT1 register by
tD = PWMDAT1 × 2 × tCORE
Therefore, a PWMDAT1 value of 0x00A (= 10), introduces
a 426 ns delay between the turn-off on any PWM signal (0H,
for example) and the turn-on of its complementary signal (0L).
The amount of the dead time can, therefore, be programmed in
increments of 2tCORE (or 49 ns for a 41.78 MHz core clock).
04955-
027
PWM0H
PWM0L
PWM1H
PWM1L
PWM2H
PWM2L
PWMCON
PWMDAT0
PWMDAT1
PWMDAT2
PWMCH0
PWMCH1
PWMCH2
CONFIGURATION
REGISTERS DUTY CYCLE
REGISTERS
3-PHASE
PWM TIMING
UNIT
PWMEN
OUTPUT
CONTROL
UNIT
PWM
SHUTDOWN
CONTROLLER
PWMCFG
GATE
DRIVE
UNIT
PWMSYNC
PWMTRIP
TO INTERRUPT
CONTROLLER
SYNC
CORE CLOCK
Figure 68. Overview of the PWM Controller
相關PDF資料
PDF描述
VI-B2L-IY-F2 CONVERTER MOD DC/DC 28V 50W
VJ2225A392KBAAT4X CAP CER 3900PF 50V 10% NP0 2225
VI-J1Z-IW-F3 CONVERTER MOD DC/DC 2V 40W
VI-B2K-IY-F3 CONVERTER MOD DC/DC 40V 50W
VJ2225A392KBBAT4X CAP CER 3900PF 100V 10% NP0 2225
相關代理商/技術參數
參數描述
ADUC7029BBCZ62I-RL 功能描述:IC MCU 12BIT 62KB FLASH 49BGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND
ADUC7029BBCZ62-RL 功能描述:IC MCU 12BIT 62KB FLASH 49BGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND
ADUC702X 制造商:AD 制造商全稱:Analog Devices 功能描述:Precision Analog Microcontroller 12-bit Analog I/O, ARM7TDMI MCU
ADUC702X_1 制造商:AD 制造商全稱:Analog Devices 功能描述:Precision Analog Microcontroller 12-bit Analog I/O, ARM7TDMI MCU
ADUC7030 制造商:AD 制造商全稱:Analog Devices 功能描述:Integrated Precision Battery Sensor For Automotive
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*