- 您現在的位置：買賣IC網 > PDF目錄374039 > ADUC7027BST62 (ANALOG DEVICES INC) Precision Analog Microcontroller 12-bit Analog I/O, ARM7TDMI MCU PDF資料下載
參數資料
| 型號： | ADUC7027BST62 |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | Precision Analog Microcontroller 12-bit Analog I/O, ARM7TDMI MCU |
| 中文描述： | 32-BIT, FLASH, 45.5 MHz, MICROCONTROLLER, PQFP80 |
| 封裝： | PLASTIC, LQFP-80 |
| 文件頁數： | 57/80頁 |
| 文件大小： | 840K |
| 代理商： | ADUC7027BST62 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁當前第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁
Preliminary Technical Data
ADuC702x Series
Rev. PrB | Page 57 of 80
SERIAL PERIPHERAL INTERFACE
The ADuC702x integrates a complete hardware Serial
Peripheral Interface (SPI) on-chip. SPI is an industry standard
synchronous serial interface that allows eight bits of data to be
synchronously transmitted and received simultaneously, i.e., full
duplex up to a maximum bit rate of 5.6Mbs. The SPI Port can
be configured for Master or Slave operation and typically
consists of four pins, namely:
MISO (Master In, Slave Out Data I/O Pin)
The MISO (master in slave out) pin is configured as an input
line in master mode and an output line in slave mode. The
MISO line on the master (data in) should be connected to the
MISO line in the slave device (data out). The data is transferred
as byte wide (8-bit) serial data, MSB first.
MOSI (Master Out, Slave In Pin)
The MOSI (master out slave in) pin is configured as an output
line in master mode and an input line in slave mode.
The MOSI line on the master (data out) should be connected to
the MOSI line in the slave device (data in). The data is
transferred as byte wide (8-bit) serial data, MSB first.
SCL (Serial Clock I/O Pin)
The master serial clock (SCL) is used to synchronize the data
being transmitted and received through the MOSI SCL period.
Therefore, a byte is transmitted/received after eight SCL
periods. The SCL pin is configured as an output in master mode
and as an input in slave mode.
In master mode polarity and phase of the clock are controlled
by the SPICON register, and the bit-rate is defined in the
SPIDIV register as follow:
)
1
2
SPIDIV
f
f
coreclock
+
k
serialcloc
×
=
The maximum serial bit clock frequency is 1/8 of the core clock
which, based on a maximum core clock frequency of 45MHz is
just above 5.6Mbs.
In slave mode the SPICON register must be configured with the
phase and polarity of the expected input clock.
In both master and slave modes, the data is transmitted on one
edge of the SCL signal and sampled on the other. It is important
therefore that the polarity and phase are configured the same
for the master and slave devices.
Chip Select (CS) Input Pin
In SPI Slave Mode, a transfer is initiated by the assertion of CS
which is an active low input signal. The SPI port will then
transmit and receive 8-bit data until the transfer is concluded by
desassertion of CS . In slave mode CS is always an input.
SPI registers definition
The following MMR registers are used to control the SPI
interface:
-
SPICON:
16-bit control register
-
SPISTA:
8-bit read only status register
-
SPIDIV:
8-bit serial clock divider register
-
SPITX:
8-bit write only transmit register
-
SPIRX:
8-bit read only receive register
Table 46: SPICON MMR Bit Descriptions
Bit
15-13
12
Description
Reserved
Continuous transfer enable
Set
by user to enable continuous transfer.
In master mode the transfer will continue until no valid data is available in the TX register. CS will be asserted and remain
asserted for the duration of each 8-bit serial transfer until TX is empty
Cleared
by user to disable continuous transfer. Each transfer consists of a single 8-bit serial transfer. If valid data exists in
the SPITX register then a new transfer is initiated after a stall period
Loop back enable
Set
by user to connect MISO to MOSI and test software
Cleared
by user to be in normal mode
Slave output enable
Set
by user to enable the slave output
Cleared
by user to disable slave output
Slave select input enable
Set
by user in master mode to enable the output
SPIRX overflow overwrite enable
Set by user, the valid data in the RX register is overwritten by the new serial byte received
11
10
9
8
相關PDF資料 |
PDF描述 |
|---|---|
| ADUC702X | Precision Analog Microcontroller 12-bit Analog I/O, ARM7TDMI MCU |
| ADUC7020 | Precision Analog Microcontroller 12-bit Analog I/O, ARM7TDMI MCU |
| ADUC702 | 5 AMP MINIATURE POWER RELAY |
| ADUC814ARU-REEL7 | Circular Connector; MIL SPEC:MIL-DTL-38999 Series I; Body Material:Metal; Series:LJT; No. of Contacts:37; Connector Shell Size:25; Connecting Termination:Crimp; Circular Shell Style:Jam Nut Receptacle; Body Style:Straight RoHS Compliant: No |
| ADUC814BRU | Circular Connector; MIL SPEC:MIL-DTL-38999 Series I; Body Material:Metal; Series:LJT; No. of Contacts:37; Connector Shell Size:25; Connecting Termination:Crimp; Circular Shell Style:Jam Nut Receptacle; Body Style:Straight RoHS Compliant: No |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADUC7027BSTZ62 | 功能描述:IC MCU FLASH 62K ANLG I/0 80LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 標準包裝:250 系列:LPC11Uxx 核心處理器:ARM? Cortex?-M0 芯體尺寸:32-位 速度:50MHz 連通性:I²C，Microwire，SPI，SSI，SSP，UART/USART，USB 外圍設備:欠壓檢測/復位，POR，WDT 輸入/輸出數:40 程序存儲器容量:96KB（96K x 8） 程序存儲器類型:閃存 EEPROM 大小:4K x 8 RAM 容量:10K x 8 電壓 - 電源 (Vcc/Vdd):1.8 V ~ 3.6 V 數據轉換器:A/D 8x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:48-LQFP 包裝:托盤 其它名稱:568-9587 |
| ADUC7027BSTZ62I | 功能描述:IC MCU FLASH 62K ANLG I2C 80LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND |
| ADUC7027BSTZ62I-RL | 制造商:Analog Devices 功能描述: |
| ADUC7027BSTZ62-RL | 功能描述:IC MCU 12BIT 1MSPS UART 80-LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND |
| ADUC7028BBCZ62 | 功能描述:IC MCU FLASH 62K 12BIT RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND |
發(fā)布緊急采購，3分鐘左右您將得到回復。