參數資料
型號： ADT7463
廠商： Analog Devices, Inc.
英文描述： dB COOL Remote Thermal Controller and Voltage Monitor
中文描述： 分貝超酷的遠程熱控制器和電壓監視器
文件頁數： 34/53頁
文件大?。?/td> 719K
代理商： ADT7463
REV. 0
–34–
ADT7463
Table X. Register 0x36 – Dynamic T
MIN
Control Register 1 (Power-On Default = 0x00)
Bit
Name R/W
Description
<0>
CYR2
Read/Write
MSB of 3-Bit Remote 2 Cycle Value. The other two bits of the code reside in Dynamic T
MIN
Control Register 2 (Reg. 0x37). These three bits define the delay time between making sub-
sequent T
MIN
adjustments in the control loop, in terms of number of monitoring cycles.
The system will have associated thermal time constants that need to be found to optimize
the response of fans and the control loop.
<1>
V
CCP
LO
Read/Write
V
CCP
LO = 1. When the power is supplied from 3.3VSTANDBY and the core voltage
(V
CCP
) drops below its V
CCP
low limit value (Reg. 0x46), the following occurs:
Status bit 1 in Status Register 1 gets set.
SMBALERT
gets generated if enabled.
PROCHOT
monitoring is disabled.
Dynamic T
MIN
control is disabled.
The device is prevented from entering shutdown.
Everything re-enabled once V
CCP
increases above V
CCP
low limit.
<2>
PHTR1
Read/Write
PHTR1 = 1 copies the Remote 1 current temperature to the Remote 1 Operating Point
Register if
THERM
gets asserted. The operating point will contain the temperature at
which
THERM
is asserted. This allows the system to run as quietly as possible without
system performance being affected. PHTR1 = 0 ignores any
THERM
assertions on the
THERM
pin. The Remote 1 Operating Point Register will reflect its programmed value.
<3>
PHTL
Read/Write
PHTL = 1 copies the local channel’s current temperature to the Local Operating Point
Register if
THERM
gets asserted. The operating point will contain the temperature at
which
THERM
is asserted. This allows the system to run as quietly as possible without
system performance being affected. PHTL = 0 ignores any
THERM
assertions on the
THERM
pin. The Local Temp Operating Point Register will reflect its programmed value
.
<4>
PHTR2
Read/Write
PHTR2 = 1 copies the Remote 2 current temperature to the Remote 2 Operating Point
Register if
THERM
gets asserted. The operating point will contain the temperature at
which
THERM
is asserted. This allows the system to run as quietly as possible without
system performance being affected. PHTR2 = 0 ignores any
THERM
assertions on the
THERM
pin. The Remote 2 Operating Point Register will reflect its programmed value.
<5>
R1T
Read/Write
R1T = 1 enables
dynamic
T
MIN
control on the Remote 1
Temperature channel. The
chosen T
MIN
value will be dynamically adjusted based on the current temperature, oper-
ating point, and high and low limits for this zone. R1T = 0 disables dynamic T
MIN
con-
trol. The T
MIN
value chosen will not be adjusted and the channel will behave as described
in the Automatic Fan Control section.
<6>
LT
Read/Write
LT = 1 enables dynamic T
MIN
control on the Local Temperature channel. The chosen
T
MIN
value will be dynamically adjusted based on the current temperature, operating
point, and high and low limits for this zone. LT = 0 disables dynamic T
MIN
control. The
T
MIN
value chosen will not be adjusted and the channel will behave as described in the
Automatic Fan Control section.
<7>
R2T
Read/Write
R2T = 1 enables dynamic T
MIN
control on the Remote 2 Temperature channel. The
chosen T
MIN
value will be dynamically adjusted based on the current temperature,
operating point, and high and low limits for this zone. R2T = 0 disables dynamic T
MIN
control. The T
MIN
value chosen will not be adjusted and the channel will behave as
described in the Automatic Fan Control section.
*
This register becomes read-only when the Configuration Register 1 Lock bit is set to 1. Any subsequent attempts to write to this register will fail.
相關PDF資料
PDF描述
ADT7463ARQ dB COOL Remote Thermal Controller and Voltage Monitor
ADT7466 dBCool Remote Thermal Controller and Voltage Monitor
ADT7466ARQZ dBCool Remote Thermal Controller and Voltage Monitor
ADT7466ARQZ-REEL dBCool Remote Thermal Controller and Voltage Monitor
ADT7466ARQZ-REEL7 dBCool Remote Thermal Controller and Voltage Monitor
相關代理商/技術參數
參數描述
ADT7463ARQ 功能描述:IC REMOTE THERMAL CTRLR 24-QSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:dBCool® 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓?fù)?ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6
ADT7463ARQ-REEL 功能描述:IC SENSOR TEMP FAN-CTRL 24QSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:dBCool® 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓?fù)?ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6
ADT7463ARQ-REEL7 功能描述:IC SENSOR TEMP FAN-CTRL 24QSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:dBCool® 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓?fù)?ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6
ADT7463ARQZ 功能描述:馬達/運動/點火控制器和驅動器 SYS MGMT CNTRLR IC RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
ADT7463ARQZ-R7 功能描述:板上安裝溫度傳感器 SYS MGMT CNTRLR IC RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*