- 您現在的位置：買賣IC網 > Datasheet目錄39 > ADT7461ARMZ-2R (ON Semiconductor)IC TEMP SENSOR DGTL 2CH 8-MSOP Datasheet資料下載
參數資料
| 型號： | ADT7461ARMZ-2R |
| 廠商： | ON Semiconductor |
| 文件頁數： | 9/20頁 |
| 文件大?。?/td> | 268K |
| 描述： | IC TEMP SENSOR DGTL 2CH 8-MSOP |
| 產品變化通告： | MFG CHG Notification ADI to ON Semi |
| 標準包裝： | 3,000 |
| 功能： | 溫度監控系統（傳感器） |
| 傳感器類型： | 內部和外部 |
| 感應溫度： | 0°C ~ 127°C，-55°C ~ 150°C |
| 精確度： | ±3°C |
| 拓?fù)洌?/td> | ADC，比較器，多路復用器，寄存器庫 |
| 輸出類型： | 2 線 SMBus? |
| 輸出警報： | 是 |
| 輸出風扇： | 是 |
| 電源電壓： | 3 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 120°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-TSSOP，8-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | Micro8? |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁
ADT7461
http://onsemi.com
9
Table 7. TEMPERATURE DATA FORMAT
(LOCAL AND REMOTE TEMPERATURE HIGH BYTE)
Temperature
Binary
Offset Binary
(Note 1)
55癈
0 000 0000
(Note 2)
0 000 1001
0癈
0 000 0000
0 100 0000
+1癈
0 000 0001
0 100 0001
+10癈
0 000 1010
0 100 1010
+25癈
0 001 1001
0 101 1001
+50癈
0 011 0010
0 111 0010
+75癈
0 100 1011
1 000 1011
+100癈
0 110 0100
1 010 0100
+125癈
0 111 1101
1 011 1101
+127癈
0 111 1111
1 011 1111
+150癈
0 111 1111
(Note 3)
1 101 0110
1. Offset binary scale temperature values are offset by 64癈.
2. Binary scale temperature measurement returns 0癈 for all
temperatures < 0癈.
3. Binary scale temperature measurement returns 127癈 for all
temperatures > 127癈.
The user can switch between measurement ranges at any
time. Switching the range also switches the data format. The
next temperature result following the switching is reported
back to the register in the new format. However, the
contents of the limit registers are not changed. The user must
ensure that the limit registers are reprogrammed, as
necessary, when the data format changes. See the Limit
Registers section for more information.
ADT7461 Registers
The ADT7461 contains a total of 22 8-bit registers. These
registers are used to store the results of remote and local
temperature measurements and high and low temperature
limits and to configure and control the device. A description
of these registers follows. Additional details are provided in
Table 8 to Table 12.
Address Pointer Register
The address pointer register does not have or require an
address, as the first byte of every write operation is
automatically written to this register. The data in this first
byte always contains the address of another register on the
ADT7461, which is stored in the address pointer register.
This register address is written to by the second byte of a
write operation or is used for a subsequent read operation.
The power-on default value of the address pointer register
is 0x00. Therefore, if a read operation is performed
immediately after power-on, without first writing to the
address pointer, the value of the local temperature is
returned, since its register address is 0x00.
Temperature Value Registers
The ADT7461 has three registers to store the results of
local and remote temperature measurements. These
registers can only be written to by the ADC and can be read
by the user over the SMBus. The local temperature value
register is at Address 0x00.
The external temperature value high byte register is at
Address 0x01, with the low byte register at Address 0x10.
The power-on default for all three registers is 0x00.
Configuration Register
The configuration register is Address 0x03 at read and
Address 0x09 at write. Its power-on default is 0x00. Only
four bits of the configuration register are used. Bits 0, 1, 3,
and 4 are reserved and should not be written to by the user.
Bit 7 of the configuration register is used to mask the
ALERT
output. If Bit 7 is 0, the ALERT
output is enabled.
This is the power-on default. If Bit 7 is set to 1, the ALERT
output is disabled. This only applies if Pin 6 is configured as
ALERT
. If Pin 6 is configured as THERM2
, the value of
Bit 7 has no effect.
If Bit 6 is set to 0 (the power-on default), the device is in
operating mode with the ADC converting. If Bit 6 is set to
1, the device is in standby mode and the ADC does not
convert. The SMBus does, however, remain active in
standby mode, so values can be read from or written to the
ADT7461 via the SMBus in this mode. The ALERT
and
THERM
outputs are also active in standby mode. Changes
made to the registers in standby mode that affect the
THERM
or ALERT
outputs cause these signals to be
updated.
Bit 5 determines the configuration of Pin 6 on the
ADT7461. If Bit 5 is 0 (default), then Pin 6 is configured as
an ALERT
output. If Bit 5 is 1, then Pin 6 is configured as
a THERM2
output. Bit 7, the ALERT
mask bit, is only
active when Pin 6 is configured as an ALERT
output. If
Pin 6 is set up as a THERM2
output, then Bit 7 has no effect.
Bit 2 sets the temperature measurement range. If Bit 2 is
0 (default), the temperature measurement range is set
between 0癈 to +127癈. Setting Bit 2 to 1 means that the
measurement range is set to the extended temperature range.
Table 8. CONFIGURATION REGISTER BIT
ASSIGNMENTS
Bit
Name
Function
Power-On
Default
7
MASK1
0 = ALERT
Enabled
1 = ALERT
Masked
0
6
RUN/STOP
0 = Run
1 = Standby
0
5
ALERT
/
THERM2
0 = ALERT
1 = THERM2
0
4, 3
Reserved
0
2
Temperature
Range Select
0 = 0癈 to 127癈
1 = Extended Range
0
1, 0
Reserved
0
相關PDF資料 |
PDF描述 |
|---|---|
| ADT7463ARQZ-REEL | IC REMOTE THERMAL CTRLR 24-QSOP |
| ADT7476AARQZ-R | IC REMOTE THERMAL CTLR 24QSOP |
| ADT7481ARMZ-1RL | IC SENSOR TEMP 2CH ALARM 10MSOP |
| ADT7482ARMZ-REEL | IC SENSOR TEMP 2CH ALARM 10MSOP |
| ADT7485AARMZ-R | IC TEMP/VOLT DGL SENS SST 10MSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADT7461ARMZ-2REEL | 功能描述:IC SENSOR TEMP DGTL 2CH 8MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓?fù)?ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| ADT7461ARMZ-2REEL7 | 功能描述:IC SENSOR TEMP DGTL 2CH 8MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓?fù)?ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| ADT7461ARMZ-2RL7 | 功能描述:板上安裝溫度傳感器 EXT TMP RGE IC 1C TDM SRC RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| ADT7461ARMZ-R2 | 制造商:ON Semiconductor 功能描述:ADT7461ARMZ-2REEL |
| ADT7461ARMZ-R7 | 功能描述:板上安裝溫度傳感器 EXT TMP RGE IC 1C TDM SRC RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
發布緊急采購，3分鐘左右您將得到回復。