參數資料
型號： ADSP-2187LBST-160
廠商： ANALOG DEVICES INC
元件分類： 數字信號處理
英文描述： DSP Microcomputer
中文描述： 24-BIT, 26.3 MHz, OTHER DSP, PQFP100
封裝： MS-026BED, LQFP-100
文件頁數： 13/32頁
文件大?。?/td> 223K
代理商： ADSP-2187LBST-160
ADSP-2187L
–13–
REV. 0
INSTRUCTION SET DESCRIPTION
The ADSP-2187L assembly language instruction set has an
algebraic syntax that was designed for ease of coding and read-
ability. The assembly language, which takes full advantage of
the processor’s unique architecture, offers the following benefits:
The algebraic syntax eliminates the need to remember cryptic
assembler mnemonics. For example, a typical arithmetic add
instruction, such as AR = AX0 + AY0, resembles a simple
equation.
Every instruction assembles into a single, 24-bit word that can
execute in a single instruction cycle.
The syntax is a superset ADSP-2100 Family assembly lan-
guage and is completely source and object code compatible
with other family members. Programs may need to be relo-
cated to utilize on-chip memory and conform to the ADSP-
2187L’s interrupt vector and reset vector map.
Sixteen condition codes are available. For conditional jump,
call, return or arithmetic instructions, the condition can be
checked and the operation executed in the same instruction
cycle.
Multifunction instructions allow parallel execution of an
arithmetic instruction with up to two fetches or one write to
processor memory space during a single instruction cycle.
DESIGNING AN EZ-ICE-COMPATIBLE SYSTEM
The ADSP-2187L has on-chip emulation support and an ICE-
Port, a special set of pins that interface to the EZ-ICE. These
features allow in-circuit emulation without replacing the target
system processor by using only a 14-pin connection from the
target system to the EZ-ICE. Target systems must have a 14-pin
connector to accept the EZ-ICE’s in-circuit probe, a 14-pin plug.
See the ADSP-2100 Family EZ-Tools data sheet for complete in-
formation on ICE products.
Issuing the chip reset command during emulation causes the
DSP to perform a full chip reset, including a reset of its memory
mode. Therefore, it is vital that the mode pins are set correctly
PRIOR to issuing a chip reset command from the emulator user
interface. If you are using a passive method of maintaining
mode information (as discussed in Setting Memory Modes)
then it does not matter that the mode information is latched by
an emulator reset. However, if you are using the
RESET
pin as
a method of setting the value of the mode pins, then you have to
take into consideration the effects of an emulator reset.
The ICE-Port interface consists of the following ADSP-2187L
pins:
EBR
EBG
ERESET
EMS
EINT
ECLK
ELIN
ELOUT
EE
These ADSP-2187L pins must be connected
only
to the EZ-ICE
connector in the target system. These pins have no function ex-
cept during emulation, and do not require pull-up or pull-down
resistors. The traces for these signals between the ADSP-2187L
and the connector must be kept as short as possible, no longer
than three inches.
The following pins are also used by the EZ-ICE:
BR
BG
RESET
GND
The EZ-ICE uses the EE (emulator enable) signal to take con-
trol of the ADSP-2187L in the target system. This causes the
processor to use its
ERESET
,
EBR
and
EBG
pins instead of the
RESET
,
BR
and
BG
pins. The
BG
output is three-stated. These
signals do not need to be jumper-isolated in your system.
The EZ-ICE
connects to your target system via a ribbon cable
and a 14-pin female plug. The ribbon cable is 10 inches in
length with one end fixed to the EZ-ICE. The female plug is
plugged onto the 14-pin connector (a pin strip header) on the
target board.
One method of ensuring that the values located on the mode
pins are those desired is to construct a circuit like the one shown
in Figure 10. This circuit forces the value located on the Mode
A pin to logic high; regardless if it latched via the
RESET
or
ERESET
pin.
ERESET
RESET
ADSP-2187L
MODE A/PFO
PROGRAMMABLE I/O
1k
V
Figure 10. Mode A Pin/EZ-ICE Circuit
相關PDF資料
PDF描述
ADSP-2187LBST-210 DSP Microcomputer
ADSP-2189MBST-266 DSP Microcomputer
ADSP-2189NBCA-320 DSP Microcomputer
ADSP-2189NBST-320 DSP Microcomputer
ADSP-2189NKCA-320 DSP Microcomputer
相關代理商/技術參數
參數描述
ADSP-2187LBST-210 制造商:Analog Devices 功能描述:DSP Fixed-Point 16-Bit 52.5MHz 52.5MIPS 100-Pin LQFP 制造商:Rochester Electronics LLC 功能描述:16BIT DSP 40 MHZ 64K WORDS RAM 100 LEAD - Bulk 制造商:Analog Devices 功能描述:IC MICROCOMPUTER 16-BIT
ADSP-2187LBSTZ-160 制造商:Analog Devices 功能描述:DSP FIX PT 16BIT 40MHZ 40MIPS 100LQFP - Trays
ADSP-2187LBSTZ-1602 制造商:AD 制造商全稱:Analog Devices 功能描述:DSP Microcomputer
ADSP-2187LBSTZ-210 功能描述:IC DSP CONTROLLER 16BIT 100-TQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:ADSP-21xx 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤
ADSP-2187LBSTZ-2102 制造商:AD 制造商全稱:Analog Devices 功能描述:DSP Microcomputer
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*