- 您現在的位置：買賣IC網 > PDF目錄374036 > ADSP-2186M (Analog Devices, Inc.) Cap-Free, NMOS, 150mA Low Dropout Regulator with Reverse Current Protection PDF資料下載
參數資料
| 型號： | ADSP-2186M |
| 廠商： | Analog Devices, Inc. |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | Cap-Free, NMOS, 150mA Low Dropout Regulator with Reverse Current Protection |
| 中文描述： | 無電容，NMOS管，150mA的低壓差穩壓器的反向電流保護 |
| 文件頁數： | 11/40頁 |
| 文件大?。?/td> | 288K |
| 代理商： | ADSP-2186M |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
REV. 0
ADSP-2186M
–11–
CLKIN
XTAL
CLKOUT
DSP
Figure 3. External Crystal Connections
RESET
The
RESET
signal initiates a master reset of the ADSP-2186M.
The
RESET
signal must be asserted during the power-up
sequence to assure proper initialization.
RESET
during initial
power-up must be held long enough to allow the internal clock
to stabilize. If
RESET
is activated any time after power-up, the
clock continues to run and does not require stabilization time.
The power-up sequence is defined as the total time required for the
crystal oscillator circuit to stabilize after a valid V
DD
is applied to
the processor, and for the internal phase-locked loop (PLL) to lock
onto the specific crystal frequency. A minimum of 2000 CLKIN
cycles ensures that the PLL has locked but does not include the
crystal oscillator start-up time. During this power-up sequence
the
RESET
signal should be held low. On any subsequent resets,
the
RESET
signal must meet the minimum pulsewidth specifi-
cation, t
RSP
.
The
RESET
input contains some hysteresis; however, if an
RC circuit is used to generate the
RESET
signal, the use of an
external Schmidt trigger is recommended.
The master reset sets all internal stack pointers to the empty stack
condition, masks all interrupts, and clears the MSTAT register.
When
RESET
is released, if there is no pending bus request and
the chip is configured for booting, the boot-loading sequence is
Table II. Modes of Operation
MODE D
MODE C
MODE B
MODE A
Booting Method
X
0
0
0
BDMA feature is used to load the first 32 program memory words from
the byte memory space. Program execution is held off until all 32 words
have been loaded. Chip is configured in Full Memory Mode.
1
No automatic boot operations occur. Program execution starts at external
memory location 0. Chip is configured in Full Memory Mode. BDMA can
still be used, but the processor does not automatically use or wait for these
operations.
BDMA feature is used to load the first 32 program memory words from
the byte memory space. Program execution is held off until all 32 words
have been loaded. Chip is configured in Host Mode.
IACK
has active
pull-down. (REQUIRES ADDITIONAL HARDWARE).
IDMA feature is used to load any internal memory as desired. Program
execution is held off until internal program memory location 0 is written
to. Chip is configured in Host Mode.
IACK
has active pull-down.
1
BDMA feature is used to load the first 32 program memory words from
the byte memory space. Program execution is held off until all 32 words
have been loaded. Chip is configured in Host Mode;
IACK
requires exter-
nal pull down. (REQUIRES ADDITIONAL HARDWARE)
IDMA feature is used to load any internal memory as desired. Program
execution is held off until internal program memory location 0 is written
to. Chip is configured in Host Mode.
IACK
requires external pull-down.
1
X
0
1
0
0
1
0
0
0
1
0
1
1
1
0
0
1
1
0
1
NOTE
1
Considered as standard operating settings. Using these configurations allows for easier design and better memory management.
performed. The first instruction is fetched from on-chip pro-
gram memory location 0x0000 once boot loading completes.
Power Supplies
The ADSP-2186M has separate power supply connections for
the internal (V
DDINT
) and external (V
DDEXT
) power supplies.
The internal supply must meet the 2.5 V requirement. The
external supply can be connected to either a 2.5 V or 3.3 V supply.
All external supply pins must be connected to the same supply.
All input and I/O pins can tolerate input voltages up to 3.6 V,
regardless of the external supply voltage. This feature provides
maximum flexibility in mixing 2.5 V and 3.3 V components.
MODES OF OPERATION
Setting Memory Mode
Memory Mode selection for the ADSP-2186M is made during
chip reset through the use of the Mode C pin. This pin is multi-
plexed with the DSP’s PF2 pin, so care must be taken in how
the mode selection is made. The two methods for selecting the
value of Mode C are active and passive.
Passive Configuration
Passive Configuration involves the use a pull-up or pull-down
resistor connected to the Mode C pin. To minimize power con-
sumption, or if the PF2 pin is to be used as an output in the DSP
application, a weak pull-up or pull-down, on the order of 10 k
,
can be used. This value should be sufficient to pull the pin to the
desired level and still allow the pin to operate as a programmable
flag output without undue strain on the processor’s output driver.
For minimum power consumption during power-down, recon-
figure PF2 to be an input, as the pull-up or pull-down will
hold the pin in a known state, and will not switch.
相關PDF資料 |
PDF描述 |
|---|---|
| ADSP-2186MKST-300 | DSP Microcomputer |
| ADSP-2186MKCA-300 | CAP 33PF 50V 1206 |
| ADSP-2186MBCA-266 | DSP Microcomputer |
| ADSP-2186 | DSP Microcomputer |
| ADSP-2186BST-115 | DSP Microcomputer |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADSP-2186MBCA-266 | 制造商:Analog Devices 功能描述:DSP Fixed-Point 16-Bit 66MHz 66MIPS 144-Pin CSP-BGA 制造商:Rochester Electronics LLC 功能描述:8K/8K 16 BIT DSP 66MHZ 2.5V MINI BGA - Bulk |
| ADSP-2186MBST-266 | 制造商:Analog Devices 功能描述:DSP Fixed-Point 16-Bit 66MHz 66MIPS 100-Pin LQFP 制造商:Rochester Electronics LLC 功能描述:75 MHZ 16-BIT DSP,2.5V,8K/8K SRAM - Bulk 制造商:Analog Devices 功能描述:IC MICROCOMPUTER 16-BIT |
| ADSP-2186MBST-266R | 制造商:Analog Devices 功能描述:DSP Fixed-Point 16-Bit 66MHz 66MIPS 100-Pin LQFP T/R |
| ADSP-2186MBSTZ-266 | 功能描述:IC DSP CONTROLLER 16BIT 100LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:ADSP-21xx 標準包裝:40 系列:TMS320DM64x, DaVinci™ 類型:定點 接口:I²C，McASP，McBSP 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:160kB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:0°C ~ 90°C 安裝類型:表面貼裝 封裝/外殼:548-BBGA，F(xiàn)CBGA 供應商設備封裝:548-FCBGA（27x27） 包裝:托盤 配用:TMDSDMK642-0E-ND - DEVELPER KIT W/NTSC CAMERA296-23038-ND - DSP STARTER KIT FOR TMS320C6416296-23059-ND - FLASHBURN PORTING KIT296-23058-ND - EVAL MODULE FOR DM642TMDSDMK642-ND - DEVELOPER KIT W/NTSC CAMERA |
| ADSP-2186MBSTZ266R | 功能描述:IC DSP CONTROLLER 16BIT 100LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:ADSP-21xx 標準包裝:40 系列:TMS320DM64x, DaVinci™ 類型:定點 接口:I²C，McASP，McBSP 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:160kB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:0°C ~ 90°C 安裝類型:表面貼裝 封裝/外殼:548-BBGA，F(xiàn)CBGA 供應商設備封裝:548-FCBGA（27x27） 包裝:托盤 配用:TMDSDMK642-0E-ND - DEVELPER KIT W/NTSC CAMERA296-23038-ND - DSP STARTER KIT FOR TMS320C6416296-23059-ND - FLASHBURN PORTING KIT296-23058-ND - EVAL MODULE FOR DM642TMDSDMK642-ND - DEVELOPER KIT W/NTSC CAMERA |
發布緊急采購，3分鐘左右您將得到回復。