- 您現在的位置：買賣IC網 > PDF目錄374036 > ADSP-2186L (Analog Devices, Inc.) Cap-Free, NMOS, 150mA Low Dropout Regulator with Reverse Current Protection PDF資料下載
參數資料
| 型號： | ADSP-2186L |
| 廠商： | Analog Devices, Inc. |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | Cap-Free, NMOS, 150mA Low Dropout Regulator with Reverse Current Protection |
| 中文描述： | 無電容，NMOS管，150mA的低壓差穩壓器的反向電流保護 |
| 文件頁數： | 14/34頁 |
| 文件大?。?/td> | 256K |
| 代理商： | ADSP-2186L |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁
ADSP-2186L
–14–
REV. A
ESD SENSITIVITY
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection. Although
the ADSP-2186L features proprietary ESD protection circuitry, permanent damage may occur on
devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are
recommended to avoid performance degradation or loss of functionality.
ABSOLUTE MAXIMUM RATINGS*
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +4.6 V
Input Voltage . . . . . . . . . . . . . . . . . . . . –0.5 V to V
DD
+ 0.5 V
Output Voltage Swing . . . . . . . . . . . . . –0.5 V to V
DD
+ 0.5 V
Operating Temperature Range (Ambient) . . –40
°
C to +85
°
C
Storage Temperature Range . . . . . . . . . . . . –65
°
C to +150
°
C
Lead Temperature (5 sec) LQFP . . . . . . . . . . . . . . . . +280
°
C
*Stresses above those listed under Absolute Maximum Ratings may cause perma-
nent damage to the device. These are stress ratings only; functional operation of
the device at these or any other conditions above those indicated in the operational
sections of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.
TIMING PARAMETERS
GENERAL NOTES
Use the exact timing information given. Do not attempt to
derive parameters from the addition or subtraction of others.
While addition or subtraction would yield meaningful results for
an individual device, the values given in this data sheet reflect
statistical variations and worst cases. Consequently, you cannot
meaningfully add up parameters to derive longer times.
TIMING NOTES
Switching characteristics specify how the processor changes its
signals. You have no control over this timing—circuitry external
to the processor must be designed for compatibility with these
signal characteristics. Switching characteristics tell you what the
processor will do in a given circumstance. You can also use
switching characteristics to ensure that any timing requirement
of a device connected to the processor (such as memory) is
satisfied.
Timing requirements apply to signals that are controlled by
circuitry external to the processor, such as the data input for a
read operation. Timing requirements must be met to guarantee
that the processor operates correctly with other devices.
MEMORY TIMING SPECIFICATIONS
The table below shows common memory device specifications
and the corresponding ADSP-2186L timing parameters, for
your convenience.
Memory
Device
Specification
ADSP-2186L
Timing
Parameter
Timing
Parameter
Definition
Address Setup to
Write Start
Address Setup to
Write End
Address Hold Time
t
ASW
A0–A13,
xMS
Setup
before
WR
Low
A0–A13,
xMS
Setup
before
WR
Deasserted
A0–A13,
xMS
Hold
before
WR
Low
Data Setup before
WR
High
Data Hold after
WR
High
RD
Low to Data Valid
A0–A13,
xMS
to Data
Valid
t
AW
t
WRA
Data Setup Time
t
DW
Data Hold Time
t
DH
OE
to Data Valid
Address Access Time t
AA
t
RDD
xMS
=
PMS
,
DMS
,
BMS
,
CMS
,
IOMS
.
FREQUENCY DEPENDENCY FOR TIMING
SPECIFICATIONS
t
CK
is defined as 0.5 t
CKI
. The ADSP-2186L uses an input clock
with a frequency equal to half the instruction rate: a 20 MHz
input clock (which is equivalent to 50 ns) yields a 25 ns proces-
sor cycle (equivalent to 40 MHz). t
CK
values within the range of
0.5 t
CKI
period should be substituted for all relevant timing para-
meters to obtain the specification value.
Example: t
CKH
= 0.5 t
CK
– 7 ns = 0.5 (25 ns) – 7 ns = 5.5 ns
WARNING!
ESD SENSITIVE DEVICE
相關PDF資料 |
PDF描述 |
|---|---|
| ADSP-2186MBST-266 | DSP Microcomputer |
| ADSP-2186M | Cap-Free, NMOS, 150mA Low Dropout Regulator with Reverse Current Protection |
| ADSP-2186MKST-300 | DSP Microcomputer |
| ADSP-2186MKCA-300 | CAP 33PF 50V 1206 |
| ADSP-2186MBCA-266 | DSP Microcomputer |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADSP-2186L1111 | 制造商:AD 制造商全稱:Analog Devices 功能描述:DSP Microcomputer |
| ADSP-2186LBCA-160 | 制造商:Analog Devices 功能描述:DSP Fixed-Point 16-Bit 40MHz 40MIPS 144-Pin CSP-BGA 制造商:Rochester Electronics LLC 功能描述:8K/8K 16 BIT DSP 40 MIPS 3.3V MINI BGA - Bulk |
| ADSP2186LBCA-160 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| ADSP-2186LBCA-160R | 制造商:Analog Devices 功能描述:DSP Fixed-Point 16-Bit 40MHz 40MIPS 144-Pin CSP-BGA T/R |
| ADSP-2186LBCA-160R3 | 制造商:AD 制造商全稱:Analog Devices 功能描述:DSP Microcomputer |
發布緊急采購，3分鐘左右您將得到回復。