- 您現在的位置：買賣IC網 > PDF目錄374036 > ADSP-2186BST-160 (ANALOG DEVICES INC) DSP Microcomputer PDF資料下載
參數資料
| 型號： | ADSP-2186BST-160 |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 數字信號處理 |
| 英文描述： | DSP Microcomputer |
| 中文描述： | 24-BIT, 20 MHz, OTHER DSP, PQFP100 |
| 封裝： | METRIC, PLASTIC, TQFP-100 |
| 文件頁數： | 9/36頁 |
| 文件大小： | 237K |
| 代理商： | ADSP-2186BST-160 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
ADSP-2186
–9–
REV. A
Boot Memory Select (
BMS
) Disable
The ADSP-2186 also lets you boot the processor from one
external memory space while using a different external memory
space for BDMA transfers during normal operation. You can
use the
CMS
to select the first external memory space for BDMA
transfers and
BMS
to select the second external memory space
for booting. The
BMS
signal can be disabled by setting Bit 3 of
the System Control Register to 1. The System Control Register
is illustrated in Figure 7.
SYSTEM CONTROL REGISTER
9
8
7
PWAIT
PROGRAM MEMORY
WAIT STATES
BMS ENABLE
0 = ENABLED,
1 = DISABLED
DM (0
3
3FFF)
0
0
0
0
0
1
0
0
0
0
0
0
0
1
1
1
15 14 13 12 11 10
6
5
4
3
2
1
0
SPORT0 ENABLE
1 = ENABLED,
0 = DISABLED
SPORT1 ENABLE
1 = ENABLED,
0 = DISABLED
SPORT1 CONFIGURE
1 = SERIAL PORT
0 = FI, FO,
IRQ0
,
IRQ1
, SCLK
Figure 7. System Control Register
Byte Memory
The byte memory space is a bidirectional, 8-bit-wide, external
memory space used to store programs and data. Byte memory is
accessed using the BDMA feature. The BDMA Control Register is
shown in Figure 8. The byte memory space consists of 256 pages,
each of which is 16K
×
8.
BDMA CONTROL
9
8
BMPAGE
BTYPE
BDIR
0 = LOAD FROM BM
1 = STORE TO BM
BCR
0 = RUN DURING BDMA
1 = HALT DURING BDMA
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
15 14 13 12 11 10
7
6
5
4
3
2
1
0
DM (0
3
3FE3)
Figure 8. BDMA Control Register
The byte memory space on the ADSP-2186 supports read and
write operations as well as four different data formats. The byte
memory uses data bits 15:8 for data. The byte memory uses
data bits 23:16 and address bits 13:0 to create a 22-bit address.
This allows up to a 4 meg
×
8 (32 megabit) ROM or RAM to be
used without glue logic. All byte memory accesses are timed by
the BMWAIT register.
Byte Memory DMA (BDMA, Full Memory Mode)
The Byte memory DMA controller allows loading and storing of
program instructions and data using the byte memory space.
The BDMA circuit is able to access the byte memory space
while the processor is operating normally and steals only one
DSP cycle per 8-, 16- or 24-bit word transferred.
The BDMA circuit supports four different data formats that are
selected by the BTYPE register field. The appropriate number
of 8-bit accesses is done from the byte memory space to build
the word size selected. Table V shows the data formats sup-
ported by the BDMA circuit.
Table V. BDMA Data Formats
Internal
Memory Space
BTYPE
Word Size
Alignment
00
01
10
11
Program Memory
Data Memory
Data Memory
Data Memory
24
16
8
8
Full Word
Full Word
MSBs
LSBs
Unused bits in the 8-bit data memory formats are filled with 0s.
The BIAD register field is used to specify the starting address for
the on-chip memory involved with the transfer. The 14-bit BEAD
register specifies the starting address for the external byte memory
space. The 8-bit BMPAGE register specifies the starting page for
the external byte memory space. The BDIR register field selects
the direction of the transfer. The 14-bit BWCOUNT register
specifies the number of DSP words to transfer and initiates the
BDMA circuit transfers.
BDMA accesses can cross page boundaries during sequential
addressing. A BDMA interrupt is generated on the completion
of the number of transfers specified by the BWCOUNT register.
The BWCOUNT register is updated after each transfer so it can
be used to check the status of the transfers. When it reaches
zero, the transfers have finished and a BDMA interrupt is gener-
ated. The BMPAGE and BEAD registers must not be accessed
by the DSP during BDMA operations.
The source or destination of a BDMA transfer will always be
on-chip program or data memory, regardless of the values of
Mode B, PMOVLAY or DMOVLAY.
When the BWCOUNT register is written with a nonzero value,
the BDMA circuit starts executing byte memory accesses with
wait states set by BMWAIT. These accesses continue until the
count reaches zero. When enough accesses have occurred to
create a destination word, it is transferred to or from on-chip
memory. The transfer takes one DSP cycle. DSP accesses to
external memory have priority over BDMA byte memory
accesses.
The BDMA Context Reset bit (BCR) controls whether the
processor is held off while the BDMA accesses are occurring.
Setting the BCR bit to 0 allows the processor to continue opera-
tions. Setting the BCR bit to 1 causes the processor to stop
execution while the BDMA accesses are occurring, to clear the
context of the processor and start execution at address 0 when
the BDMA accesses have completed.
Internal Memory DMA Port (IDMA Port; Host Memory Mode)
The IDMA Port provides an efficient means of communication
between a host system and the ADSP-2186. The port is used to
access the on-chip program memory and data memory of the
DSP with only one DSP cycle per word overhead. The IDMA
port cannot, however, be used to write to the DSP’s memory-
mapped control registers.
相關PDF資料 |
PDF描述 |
|---|---|
| ADSP-2186KST-115 | DSP Microcomputer |
| ADSP-2186KST-133 | DSP Microcomputer |
| ADSP-2186KST-160 | DSP Microcomputer |
| ADSP-2186LBCA-160 | DSP Microcomputer |
| ADSP-2186LBST-115 | DSP Microcomputer |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADSP-2186BST-160X | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:16-Bit Digital Signal Processor |
| ADSP-2186BSTZ-115 | 制造商:Analog Devices 功能描述:DSP Fixed-Point 16-Bit 28.8MHz 28.8MIPS 100-Pin LQFP 制造商:Rochester Electronics LLC 功能描述: |
| ADSP-2186BSTZ-133 | 制造商:AD 制造商全稱:Analog Devices 功能描述:DSP Microcomputer |
| ADSP-2186BSTZ-160 | 功能描述:IC DSP CONTROLLER 16BIT 100LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:ADSP-21xx 標準包裝:40 系列:TMS320DM64x, DaVinci™ 類型:定點 接口:I²C，McASP，McBSP 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:160kB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:0°C ~ 90°C 安裝類型:表面貼裝 封裝/外殼:548-BBGA，F(xiàn)CBGA 供應商設備封裝:548-FCBGA（27x27） 包裝:托盤 配用:TMDSDMK642-0E-ND - DEVELPER KIT W/NTSC CAMERA296-23038-ND - DSP STARTER KIT FOR TMS320C6416296-23059-ND - FLASHBURN PORTING KIT296-23058-ND - EVAL MODULE FOR DM642TMDSDMK642-ND - DEVELOPER KIT W/NTSC CAMERA |
| adsp-2186kst-1 | 制造商:Analog Devices 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。