- 您現在的位置：買賣IC網 > Datasheet目錄39 > ADP5022ACBZ-6-R7 (Analog Devices Inc)IC REG TRPL BCK/LINEAR 16WLCSP Datasheet資料下載
參數資料
| 型號： | ADP5022ACBZ-6-R7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 19/28頁 |
| 文件大小： | 1071K |
| 描述： | IC REG TRPL BCK/LINEAR 16WLCSP |
| 產品變化通告： | 8mm Carrier Tape Changes 28/Feb/2012 |
| 標準包裝： | 1 |
| 拓撲： | 降壓（降壓）同步（2），線性（LDO）（1） |
| 功能： | 任何功能 |
| 輸出數： | 3 |
| 頻率 - 開關： | 3MHz |
| 電壓/電流 - 輸出 1： | 1V，600mA |
| 電壓/電流 - 輸出 2： | 1.8V，600mA |
| 電壓/電流 - 輸出 3： | 2.5V，150mA |
| 帶 LED 驅動器： | 無 |
| 帶監控器： | 無 |
| 帶序列發生器： | 是 |
| 電源電壓： | 2.3 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-WFBGA，WLCSP |
| 供應商設備封裝： | 16-WLCSP |
| 包裝： | 標準包裝 |
| 其它名稱： | ADP5022ACBZ-6-R7DKR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
ADP5022
Rev. C | Page 19 of 28
APPLICATIONS INFORMATION
BUCK EXTERNAL COMPONENT SELECTION
Trade-offs between performance parameters such as efficiency
and transient response can be made by varying the choice of
external components in the applications circuit, as shown in
Figure 1.
Inductor
The high switching frequency of the ADP5022 bucks allows for
the selection of small chip inductors. For best performance, use
inductor values between 0.7 糎 and 3 糎. Suggested inductors
are shown in Table 7.
The peak-to-peak inductor current ripple is calculated using
the following equation:
L
f
V
V
V
V
I
SW
IN
OUT
IN
OUT
RIPPLE
?/DIV>
?/DIV>
?/DIV>
=
)
(
where:
f
SW
is the switching frequency.
L is the inductor value.
The minimum dc current rating of the inductor must be greater
than the inductor peak current. The inductor peak current is
calculated using the following equation:
2
)
(
RIPPLE
MAX
LOAD
PEAK
I
I
I
+
=
Inductor conduction losses are caused by the flow of current
through the inductor, which has an associated internal dc
resistance (DCR). Larger sized inductors have smaller DCR,
which may decrease inductor conduction losses. Inductor core
losses are related to the magnetic permeability of the core material.
Because the bucks are high switching frequency dc-to-dc
converters, shielded ferrite core material is recommended for
its low core losses and low EMI.
Table 7. Suggested 1.0 糎 Inductors
Vendor
Model
Dimensions
(mm)
ISAT
(mA)
DCR
(m?
Murata
LQM2MPN1R0NG0B 2.0 ?1.6 ?0.9
1400
85
Murata
LQM18FN1R0M00B 1.6 ?0.8 ?0.8
150
26
Taiyo Yuden CBMF1608T1R0M
1.6 ?0.8 ?0.8 290
90
Coilcraft
EPL2014-102ML
2.0 ?2.0 ?1.4
900
59
TDK
GLFR1608T1R0M-LR 1.6 ?0.8 ?0.8 230
80
Coilcraft
0603LS-102
1.8 ?1.69 ?1.1 400
81
Toko
MDT2520-CN
2.5 ?2.0 ?1.2
1350
85
Output Capacitor
Higher output capacitor values reduce the output voltage ripple
and improve load transient response. When choosing this value,
it is also important to account for the loss of capacitance due to
output voltage dc bias.
Ceramic capacitors are manufactured with a variety of dielec-
trics, each with a different behavior over temperature and
applied voltage. Capacitors must have a dielectric adequate
to ensure the minimum capacitance over the necessary
temperature range and dc bias conditions. X5R or X7R
dielectrics with a voltage rating of 6.3 V or 10 V are recom-
mended for best performance. Y5V and Z5U dielectrics are
not recommended for use with any dc-to-dc converter because
of their poor temperature and dc bias characteristics.
The worst-case capacitance accounting for capacitor variation
over temperature, component tolerance, and voltage is calcu-
lated using the following equation:
CEFF = COUT ?(1 TEMPCO) ?(1 TOL)
where:
C
EFF
is the effective capacitance at the operating voltage.
TEMPCO is the worst-case capacitor temperature coefficient.
TOL is the worst-case component tolerance.
In this example, the worst-case temperature coefficient
(TEMPCO) over 40癈 to +85癈 is assumed to be 15% for an
X5R dielectric. The tolerance of the capacitor (TOL) is assumed
to be 10%, and COUT is 9.2481 糉 at 1.8 V, as shown in Figure 49.
Substituting these values in the equation yields
C
EFF
= 9.2481 糉 ?(1 0.15) ?(1 0.1) = 7.0747 糉
To guarantee the performance of the bucks, it is imperative
that the effects of dc bias, temperature, and tolerances on the
behavior of the capacitors be evaluated for each application.
0
2
4
6
8
10
12
0
1
2
3
4
5
6
DC BIAS VOLTAGE (V)
Figure 49. Typical Capacitor Performance
相關PDF資料 |
PDF描述 |
|---|---|
| ADP5041ACPZ-1-R7 | IC REG TRPL BCK/LINEAR 20-LFCSP |
| ADP5042ACPZ-2-R7 | IC REG TRPL BCK/LINEAR 20LFCSP |
| ADT6402SRJZ-RL7 | IC TEMP SENS TRIP PT PP SOT-23-6 |
| ADT6501SRJZP085RL7 | IC TEMP SENSOR MICROPWR SOT23-5 |
| ADT7302ARTZ-500RL7 | IC SENSOR TEMP 13BIT DGT SOT23-6 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADP5023 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Dual 3 MHz, 800 mA Buck |
| ADP5023ACPZ-1-R7 | 功能描述:IC REG TRPL BCK/LINEAR 24LFCSP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 + 切換式 系列:- 標準包裝:2,500 系列:- 拓撲:降壓（降壓）同步（3），線性（LDO）（2） 功能:任何功能 輸出數:5 頻率 - 開關:300kHz 電壓/電流 - 輸出 1:控制器 電壓/電流 - 輸出 2:控制器 電壓/電流 - 輸出 3:控制器 帶 LED 驅動器:無 帶監控器:無 帶序列發生器:是 電源電壓:5.6 V ~ 24 V 工作溫度:-40°C ~ 85°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* |
| ADP5023ACPZ-2-R7 | 功能描述:直流/直流開關調節器 ADJ Outputs, UVLO High RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
| ADP5023ACPZ-R2 | 功能描述:直流/直流開關調節器 ADJ Outputs UVLO Low RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
| ADP5023ACPZ-R7 | 功能描述:IC REG TRPL BCK/LINEAR 24LFCSP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 + 切換式 系列:- 標準包裝:2,500 系列:- 拓撲:降壓（降壓）同步（3），線性（LDO）（2） 功能:任何功能 輸出數:5 頻率 - 開關:300kHz 電壓/電流 - 輸出 1:控制器 電壓/電流 - 輸出 2:控制器 電壓/電流 - 輸出 3:控制器 帶 LED 驅動器:無 帶監控器:無 帶序列發生器:是 電源電壓:5.6 V ~ 24 V 工作溫度:-40°C ~ 85°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* |
發布緊急采購，3分鐘左右您將得到回復。