- 您現在的位置：買賣IC網 > PDF目錄165352 > ADP1650ACBZ-R7 (ANALOG DEVICES INC) LED DISPLAY DRIVER, PBGA12 PDF資料下載
參數資料
| 型號： | ADP1650ACBZ-R7 |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 顯示驅動器 |
| 英文描述： | LED DISPLAY DRIVER, PBGA12 |
| 封裝： | 2 X 1.50 MM, ROHS COMPLIANT, WLCSP-12 |
| 文件頁數： | 19/32頁 |
| 文件大小： | 1423K |
| 代理商： | ADP1650ACBZ-R7 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
ADP1650
Rev. C | Page 26 of 32
APPLICATIONS INFORMATION
EXTERNAL COMPONENT SELECTION
Selecting the Inductor
The ADP1650 boost converter increases the battery voltage
to allow driving of one LED, whose voltage drop is higher than
the battery voltage plus the current source headroom voltage.
This allows the converter to regulate the LED current over the
entire battery voltage range and with a wide variation of LED
forward voltage.
The inductor saturation current should be greater than the sum
of the dc input current and half the inductor ripple current. A
reduction in the effective inductance due to saturation increases
the inductor current ripple. Table 18 provides a list of recom-
mended inductors.
Selecting the Input Capacitor
The ADP1650 requires an input bypass capacitor to supply
transient currents while maintaining constant input and output
voltages. The input capacitor carries the input ripple current,
allowing the input power source to supply only the dc current.
Increased input capacitance reduces the amplitude of the
switching frequency ripple on the battery. Due to the dc bias
characteristics of ceramic capacitors, a 0603, 6.3 V, X5R/X7R,
10 μF ceramic capacitor is preferable.
Higher value input capacitors help to reduce the input voltage
ripple and improve transient response.
To minimize supply noise, place the input capacitor as close to
the VIN pin of the ADP1650 as possible. As with the output
capacitor, a low ESR capacitor is required. Table 19 provides a
list of suggested input capacitors.
Selecting the Output Capacitor
The output capacitor maintains the output voltage and supplies
the LED current during the NFET power switch on period. It also
stabilizes the loop. The recommended capacitor is a 10 μF, 6.3 V,
X5R/X7R ceramic capacitor.
Note that dc bias characterization data is available from capa-
citor manufacturers and should be taken into account when
selecting input and output capacitors. The 6.3 V capacitors are
best for most designs. Table 20 provides a list of recommended
output capacitors.
Higher output capacitor values reduce the output voltage ripple
and improve load transient response. When choosing this value,
it is also important to account for the loss of capacitance due to
output voltage dc bias.
Ceramic capacitors have a variety of dielectrics, each with different
behavior over temperature and applied voltage. Capacitors must
have a dielectric that ensures the minimum capacitance over the
necessary temperature range and dc bias conditions. X5R or X7R
dielectrics with a voltage rating of 6.3 V or 10 V are recommended
for best performance. Y5V and Z5U dielectrics are not recom-
mended for use with any dc-to-dc converter because of their
poor temperature and dc bias characteristics.
Table 18. Suggested Inductors
Vendor
Value (μH)
Part No.
DCR (mΩ)
ISAT (A)
Dimensions L × W × H (mm)
Toko
1.0
FDSD0312
41.5
4.5
3.0 × 3.0 × 1.2
Toko
1.0
DFE2520
50
3.4
2.5 × 2.0 × 1.2
Coilcraft
1.0
XFL3010
43
2.4
3.0 × 3.0 × 1.0
Murata
1.0
LQM32P_G0
60
3
3.2 × 2.5 × 1.0
FDK
1.0
MIPS3226D
40
3
2.5 × 2.0 × 1.2
Table 19. Suggested Input Capacitors
Vendor
Value
Part No.
Dimensions L × W × H (mm)
Murata
10 μF, 6.3 V
GRM188R60J106ME47
1.6 × 0.8 × 0.8
TDK
10 μF, 6.3 V
C1608JB0J106K
1.6 × 0.8 × 0.8
Taiyo Yuden
10 μF, 6.3 V
JMK107BJ106MA
1.6 × 0.8 × 0.8
Table 20. Suggested Output Capacitors
Vendor
Value
Part No.
Dimensions L × W × H (mm)
Murata
10 μF, 6.3 V
GRM188R60J106ME47
1.6 × 0.8 × 0.8
TDK
10 μF, 6.3 V
C1608JB0J106K
1.6 × 0.8 × 0.8
Taiyo Yuden
10 μF, 6.3 V
JMK107BJ106MA
1.6 × 0.8 × 0.8
相關PDF資料 |
PDF描述 |
|---|---|
| ADP1650ACPZ-R7 | LED DISPLAY DRIVER, PDSO10 |
| ADP3157 | 5-Bit Programmable Synchronous Controller for Pentium III Processors |
| ADP3159 | 4-Bit Programmable Synchronous Buck Controllers |
| ADP3162 | 5-Bit Programmable 2-Phase Synchronous Buck Controller |
| ADP3300ART-2.7-RL7 | 2.7 V FIXED POSITIVE LDO REGULATOR, 0.17 V DROPOUT, PDSO6 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADP1650ACPZ-R7 | 功能描述:IC LED DVR PHOTO FLASH 10LSCP RoHS:是 類別:集成電路 (IC) >> PMIC - LED 驅動器 系列:- 標準包裝:6,000 系列:- 恒定電流:- 恒定電壓:- 拓撲:開路漏極，PWM 輸出數:4 內部驅動器:是 類型 - 主要:LED 閃爍器 類型 - 次要:- 頻率:400kHz 電源電壓:2.3 V ~ 5.5 V 輸出電壓:- 安裝類型:表面貼裝 封裝/外殼:8-VFDFN 裸露焊盤 供應商設備封裝:8-HVSON 包裝:帶卷 (TR) 工作溫度:-40°C ~ 85°C 其它名稱:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND |
| ADP1650CB-EVALZ | 功能描述:EVAL BOARD FOR ADP1650 RoHS:是 類別:編程器，開發系統 >> 評估板 - LED 驅動器 系列:- 標準包裝:1 系列:PowerWise® 電流 - 輸出 / 通道:20mA 輸出及類型:1，非隔離 輸出電壓:17V 特點:可調光 輸入電壓:2.7 ~ 5.5 V 已供物品:板 已用 IC / 零件:LM3508 相關產品:LM3508TLX-ND - IC LED DRVR WHT BCKLGT 9USMDLM3508TLDKR-ND - IC LED DRVR WHT BCKLGT 9MICROSMDLM3508TLCT-ND - IC LED DRVR WHT BCKLGT 9MICROSMDLM3508TLTR-ND - IC LED DRVR WHT BCKLGT 9MICROSMD |
| ADP1653 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Compact, High Efficiency, High Power Flash/Torch LED Driver with Dual Interface |
| ADP1653ACPZ-R21 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Compact, High Efficiency, High Power Flash/Torch LED Driver with Dual Interface |
| ADP1653ACPZ-R7 | 功能描述:IC LED DRVR PHOTO FLASH 16-LFCSP RoHS:是 類別:集成電路 (IC) >> PMIC - LED 驅動器 系列:- 標準包裝:60 系列:- 恒定電流:- 恒定電壓:- 拓撲:線性（LDO），PWM，升壓（升壓） 輸出數:8 內部驅動器:是 類型 - 主要:背光 類型 - 次要:RGB，白色 LED 頻率:500kHz ~ 1.5MHz 電源電壓:4.75 V ~ 26 V 輸出電壓:45V 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* 工作溫度:-40°C ~ 85°C |
發布緊急采購，3分鐘左右您將得到回復。